[Elphel-support] Fwd: 14Mpix sensor not detected
Oleg
support-list at support.elphel.com
Sun Feb 25 13:37:18 PST 2018
Hi,
14MPx is not yet supported in the current firmware but I'm working on the
driver at the moment - hopefully will have something within a couple weeks.
There's an old firmware where exposure, gains and lane phases can be set,
not much more.
Best regards,
Oleg Dzhimiev
Electronics Engineer
phone: +1 801 783 5555 x124
Elphel, Inc.
On Fri, Feb 23, 2018 at 11:23 AM, Andrey Filippov <andrey at elphel.com> wrote:
>
>
> == == == == == == Forwarded message == == == == == ==
> From : Richard Rigby<rrigby at redzone.com>
> To : <support-list at elphel.com>
> Date : Thu, 22 Feb 2018 18:28:08 -0800
> Subject : 14Mpix sensor not detected
> == == == == == == Forwarded message == == == == == ==
>
> Hello,
>
> I have a 393 board as well as one 5 Mpix sensor and one 14 Mpix sensor.
> However only the 5Mpix sensor is working.
>
> I am using the web interface to view the camera.
>
> I have tried to run the init_elphel393.py script for both sensors and it
> looks to me that the 14 Mpix sensor cannot be detected.
>
> This is the output from init_elphel393.py when only the 14 Mpix sensor is
> connected:
> [ 443.35] init_elphel393: Fan on
> [ 443.36] init_elphel393: Initialize USB hub
> [ 443.37] init_elphel393: 10389 was not detected: skipping USB hub init
> [ 443.37] init_elphel393: init_elphel393.py: ip = 192.168.0.9, mask =
> 255.255.255.0
> [ 443.38] init_elphel393: init_elphel393.py: imgsrv
> Set port number: 2323
> Set port number: 2324
> Set port number: 2325
> Set port number: 2326
> [ 443.77] init_elphel393: init_elphel393.py: auto exposure daemon
> autoexposure#0 started, daemon_bit=0x0, debug=0x1
> autoexposure#1 started, daemon_bit=0x0, debug=0x1
> autoexposure#2 started, daemon_bit=0x0, debug=0x1
> autoexposure#3 started, daemon_bit=0x0, debug=0x1
> [ 443.99] autocampars: Processing camera state: INITIALIZED
> [ 444.05] autocampars: Active sensor ports: master_port = -1
> [ 444.07] autocampars: Sensors map read from the sysfs: [none, none,
> none, none],[none, none, none, none],[none, none, none, none],[none, none,
> none, none]
> [ 444.12] autocampars: get_application_mode()->4369
> [ 444.17] autocampars: Detecting sensors for MT9P006
> [ 444.20] autocampars: Got --init command for already initialized
> camera, trying to re-initialize
> [ 444.22] autocampars: after reset - current frame on master port =
> [ 444.25] autocampars: Reset camera state to BITSTREAM
> [ 444.33] autocampars: ports:
> [ 444.35] autocampars: *System FPGA version: 0x039300da*
> [ 444.38] autocampars: *Sensor interface type: PAR12*
> [ 444.45] autocampars: *Detected sensors: [none, none, none,
> none],[none, none, none, none],[none, none, none, none],[none, none, none,
> none]*
> [ 444.48] autocampars: Reached state: SENSORS_DETECTED
> [ 444.53] autocampars: Disabling sensor port 0
> [ 444.56] autocampars: Disabling sensor port 1
> [ 444.58] autocampars: Disabling sensor port 2
> [ 444.61] autocampars: Disabling sensor port 3
> [ 444.69] autocampars: Frames: -1, -1, -1, -1
> [ 444.71] autocampars: Reached state: SENSORS_SYNCHRONIZED
> [ 444.74] autocampars: ports:
> [ 444.81] autocampars: init_cameras() start: camera_state=SENSORS_
> SYNCHRONIZED
> [ 444.86] autocampars: Collected gammas == Array
> (
> )
>
> [ 444.89] autocampars: will need to skip local frames
> [ 444.92] autocampars: Reached state PARAMETERS_PRESET
> [ 444.94] autocampars: Skipping frames
> [ 444.97] autocampars: Frame delay = 0 s
> [ 445.02] autocampars: Remaining trigger parameters:
>
> Warning: array_key_exists() expects parameter 2 to be array, null given in
> /usr/bin/autocampars.php on line 1074
>
> Warning: array_key_exists() expects parameter 2 to be array, null given in
> /usr/bin/autocampars.php on line 1085
>
> Warning: array_key_exists() expects parameter 2 to be array, null given in
> /usr/bin/autocampars.php on line 1086
>
> Warning: array_key_exists() expects parameter 2 to be array, null given in
> /usr/bin/autocampars.php on line 1091
>
> Warning: elphel_set_P_arr() expects parameter 2 to be array, null given in
> /usr/bin/autocampars.php on line 1095
> [ 445.09] autocampars: Skipping more frames
> [ 445.14] autocampars: Reached state PARAMETERS_PRESET
> [ 445.17] autocampars: Reached state INITIALIZED
> [ 445.20] autocampars: Sensors on ports: were successfully initialized
> [ 445.22] autocampars: *INITIALIZED*
> [ 445.25] autocampars: *revisions differ*
> [ 445.27] autocampars: *Log file saved as /var/log/autocampars.log*
> [ 445.32] init_elphel393: init SATA
> [ 445.32] init_elphel393: 10389 was not detected: skipping SATA init
> [ 445.32] init_elphel393: Start GPS and event logger
> Initializing Exif template: /www/pages/exif.php init noGPS nocompass
> [ 445.75] init_elphel393: /var/volatile/state already exists
> [ 445.75] init_elphel393: *DONE, log file: /var/log/init_elphel393.log*
>
>
> This is the output from init_elphel393.py when only the 14 Mpix sensor is
> connected:
> [ 45.92] init_elphel393: Fan on
> [ 45.93] init_elphel393: Initialize USB hub
> [ 45.94] init_elphel393: 10389 was not detected: skipping USB hub init
> [ 45.94] init_elphel393: init_elphel393.py: ip = 192.168.0.9, mask =
> 255.255.255.0
> [ 45.95] init_elphel393: init_elphel393.py: imgsrv
> Set port number: 2323
> Set port number: 2324
> Set port number: 2325
> Set port number: 2326
> [ 46.34] init_elphel393: init_elphel393.py: auto exposure daemon
> autoexposure#0 started, daemon_bit=0x0, debug=0x1
> autoexposure#1 started, daemon_bit=0x0, debug=0x1
> autoexposure#2 started, daemon_bit=0x0, debug=0x1
> autoexposure.c:141:main: autoexposure#2: drivers initialized
> autoexposure.c:146:main: autoexposure#2 started daemon_bit=0x0, debug=0x1
> autoexposure.c:154:main: autoexposure#2 this_frame = 0xe2
> autoexposure.c:157:main: frame 14: autoexposure#2 this_frame = 0xe2
> autoexposure#3 started, daemon_bit=0x0, debug=0x1
> [ 46.58] autocampars: Processing camera state: INITIALIZED
> [ 46.63] autocampars: Active sensor ports: 2 master_port = 2
> [ 46.66] autocampars: Sensors map read from the sysfs: [none, none,
> none, none],[none, none, none, none],[mt9p006, none, none, none],[none,
> none, none, none]
> [ 46.71] autocampars: get_application_mode()->4369
> [ 46.76] autocampars: Detecting sensors for MT9P006
> [ 46.79] autocampars: Got --init command for already initialized
> camera, trying to re-initialize
> [ 46.81] autocampars: Current frame on master port =230, sleeping to
> give daemons a chance
> [ 51.84] autocampars: Current frame on master port =280, waking up,
> daemons should be dead already
> [ 51.87] autocampars: after reset - current frame on master port =281
> [ 51.89] autocampars: Reset camera state to BITSTREAM
> [ 51.97] autocampars: ports:2
> [ 52.02] autocampars: Started detection for sensor port 2
> [ 52.05] autocampars: *System FPGA version: 0x039300da*
> [ 52.07] autocampars: *Sensor interface type: PAR12*
> [ 52.15] autocampars: *Detected sensors: [none, none, none,
> none],[none, none, none, none],[mt9p006, none, none, none],[none, none,
> none, none]*
> [ 52.17] autocampars: Reached state: SENSORS_DETECTED
> [ 52.43] autocampars: Disabling sensor port 0
> [ 52.45] autocampars: Disabling sensor port 1
> [ 52.48] autocampars: Disabling sensor port 3
> [ 52.66] autocampars: Frames: -1, -1, 0, -1
> [ 52.68] autocampars: Reached state: SENSORS_SYNCHRONIZED
> [ 52.71] autocampars: ports:2
> [ 52.76] autocampars: autocampars.php parsed configuration file
> /etc/elphel393/autocampars2.xml.
> [ 52.84] autocampars: init_cameras() start: camera_state=SENSORS_
> SYNCHRONIZED
> [ 52.89] autocampars: Collected gammas == Array
> (
> [2617] => 1
> )
>
> [ 52.95] autocampars: port 2 setting @1 init exposure: EXPOS= 1000
> [ 53.05] autocampars: port 2 setting @8 restoring exposure: EXPOS= 10000
> [ 53.08] autocampars: will need to skip local 7 frames
> [ 53.10] autocampars: Reached state PARAMETERS_PRESET
> [ 53.13] autocampars: Skipping 7 frames
> [ 53.15] autocampars: Frame delay = 0.1 s
> aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 7
> (0x7) are not available. this_frame=0x8, now=0x8
> autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to
> errors, skipping a frame
> aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 8
> (0x8) are not available. this_frame=0x9, now=0x9
> autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to
> errors, skipping a frame
> [ 54.62] autocampars: *Started camera in periodic self-triggered mode,
> period = 0.1 s*
> [ 54.65] autocampars: Reached state PARAMETERS_PRESET
> [ 54.68] autocampars: Reached state INITIALIZED
> [ 54.70] autocampars: Sensors on ports: 2 were successfully initialized
> aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 9
> (0x9) are not available. this_frame=0xa, now=0xa
> autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to
> errors, skipping a frame
> [ 54.73] autocampars: *INITIALIZED*
> [ 54.75] autocampars: *Log file saved as /var/log/autocampars.log*
> [ 54.81] init_elphel393: init SATA
> aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 10
> (0xa) are not available. this_frame=0xb, now=0xb
> autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to
> errors, skipping a frame
> [ 54.81] init_elphel393: 10389 was not detected: skipping SATA init
> [ 54.81] init_elphel393: Start GPS and event logger
> aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 11
> (0xb) are not available. this_frame=0xc, now=0xc
> autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to
> errors, skipping a frame
> Initializing Exif template: /www/pages/exif.php init noGPS nocompass
> [ 55.24] init_elphel393: /var/volatile/state already exists
> [ 55.24] init_elphel393: *DONE, log file: /var/log/init_elphel393.log*
>
> Any assistance in resolving this would be greatly appreciated.
>
>
> Kind regards,
>
> *Richard Rigby*
> Software Developer
>
>
> www.redzone.com
>
> Ph: +64 9 479 9901
>
> Fax: +64 9 479 9904
>
>
> 13 Tarndale Grove • Albany • Auckland 0632 • New Zealand
>
>
>
>
>
> _______________________________________________
> Support-list mailing list
> Support-list at support.elphel.com
> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://support.elphel.com/pipermail/support-list_support.elphel.com/attachments/20180225/533c52a5/attachment-0001.html>
More information about the Support-list
mailing list