[Elphel-support] Fwd: 14Mpix sensor not detected
Richard Rigby
rrigby at redzone.com
Sun Feb 25 13:47:13 PST 2018
Hi Oleg,
Thank you for your reply.
I will wait with great anticipation for the new driver. :)
On another note, would it be possible for me to run my own recorder
application directly on the camera and access a jpeg stream and record to a
hard drive?
We would like to build a robotic device capable of recording the video
stream and I was thinking that in stead of running the recording software
on a seperate computer, I could run it on the camera since it's already
running linux.
Kind regards,
*Richard Rigby*
Software Developer
www.redzone.com
Ph: +64 9 479 9901
Fax: +64 9 479 9904
13 Tarndale Grove • Albany • Auckland 0632 • New Zealand
On 26 February 2018 at 10:37, Oleg <support-list at support.elphel.com> wrote:
> Hi,
>
> 14MPx is not yet supported in the current firmware but I'm working on the
> driver at the moment - hopefully will have something within a couple weeks.
> There's an old firmware where exposure, gains and lane phases can be set,
> not much more.
>
> Best regards,
> Oleg Dzhimiev
> Electronics Engineer
> phone: +1 801 783 5555 x124 <+1%20801-783-5555>
> Elphel, Inc.
>
> On Fri, Feb 23, 2018 at 11:23 AM, Andrey Filippov <andrey at elphel.com>
> wrote:
>
>>
>>
>> == == == == == == Forwarded message == == == == == ==
>> From : Richard Rigby<rrigby at redzone.com>
>> To : <support-list at elphel.com>
>> Date : Thu, 22 Feb 2018 18:28:08 -0800
>> Subject : 14Mpix sensor not detected
>> == == == == == == Forwarded message == == == == == ==
>>
>> Hello,
>>
>> I have a 393 board as well as one 5 Mpix sensor and one 14 Mpix sensor.
>> However only the 5Mpix sensor is working.
>>
>> I am using the web interface to view the camera.
>>
>> I have tried to run the init_elphel393.py script for both sensors and it
>> looks to me that the 14 Mpix sensor cannot be detected.
>>
>> This is the output from init_elphel393.py when only the 14 Mpix sensor
>> is connected:
>> [ 443.35] init_elphel393: Fan on
>> [ 443.36] init_elphel393: Initialize USB hub
>> [ 443.37] init_elphel393: 10389 was not detected: skipping USB hub init
>> [ 443.37] init_elphel393: init_elphel393.py: ip = 192.168.0.9, mask =
>> 255.255.255.0
>> [ 443.38] init_elphel393: init_elphel393.py: imgsrv
>> Set port number: 2323
>> Set port number: 2324
>> Set port number: 2325
>> Set port number: 2326
>> [ 443.77] init_elphel393: init_elphel393.py: auto exposure daemon
>> autoexposure#0 started, daemon_bit=0x0, debug=0x1
>> autoexposure#1 started, daemon_bit=0x0, debug=0x1
>> autoexposure#2 started, daemon_bit=0x0, debug=0x1
>> autoexposure#3 started, daemon_bit=0x0, debug=0x1
>> [ 443.99] autocampars: Processing camera state: INITIALIZED
>> [ 444.05] autocampars: Active sensor ports: master_port = -1
>> [ 444.07] autocampars: Sensors map read from the sysfs: [none, none,
>> none, none],[none, none, none, none],[none, none, none, none],[none, none,
>> none, none]
>> [ 444.12] autocampars: get_application_mode()->4369
>> [ 444.17] autocampars: Detecting sensors for MT9P006
>> [ 444.20] autocampars: Got --init command for already initialized
>> camera, trying to re-initialize
>> [ 444.22] autocampars: after reset - current frame on master port =
>> [ 444.25] autocampars: Reset camera state to BITSTREAM
>> [ 444.33] autocampars: ports:
>> [ 444.35] autocampars: *System FPGA version: 0x039300da*
>> [ 444.38] autocampars: *Sensor interface type: PAR12*
>> [ 444.45] autocampars: *Detected sensors: [none, none, none,
>> none],[none, none, none, none],[none, none, none, none],[none, none, none,
>> none]*
>> [ 444.48] autocampars: Reached state: SENSORS_DETECTED
>> [ 444.53] autocampars: Disabling sensor port 0
>> [ 444.56] autocampars: Disabling sensor port 1
>> [ 444.58] autocampars: Disabling sensor port 2
>> [ 444.61] autocampars: Disabling sensor port 3
>> [ 444.69] autocampars: Frames: -1, -1, -1, -1
>> [ 444.71] autocampars: Reached state: SENSORS_SYNCHRONIZED
>> [ 444.74] autocampars: ports:
>> [ 444.81] autocampars: init_cameras() start:
>> camera_state=SENSORS_SYNCHRONIZED
>> [ 444.86] autocampars: Collected gammas == Array
>> (
>> )
>>
>> [ 444.89] autocampars: will need to skip local frames
>> [ 444.92] autocampars: Reached state PARAMETERS_PRESET
>> [ 444.94] autocampars: Skipping frames
>> [ 444.97] autocampars: Frame delay = 0 s
>> [ 445.02] autocampars: Remaining trigger parameters:
>>
>> Warning: array_key_exists() expects parameter 2 to be array, null given
>> in /usr/bin/autocampars.php on line 1074
>>
>> Warning: array_key_exists() expects parameter 2 to be array, null given
>> in /usr/bin/autocampars.php on line 1085
>>
>> Warning: array_key_exists() expects parameter 2 to be array, null given
>> in /usr/bin/autocampars.php on line 1086
>>
>> Warning: array_key_exists() expects parameter 2 to be array, null given
>> in /usr/bin/autocampars.php on line 1091
>>
>> Warning: elphel_set_P_arr() expects parameter 2 to be array, null given
>> in /usr/bin/autocampars.php on line 1095
>> [ 445.09] autocampars: Skipping more frames
>> [ 445.14] autocampars: Reached state PARAMETERS_PRESET
>> [ 445.17] autocampars: Reached state INITIALIZED
>> [ 445.20] autocampars: Sensors on ports: were successfully initialized
>> [ 445.22] autocampars: *INITIALIZED*
>> [ 445.25] autocampars: *revisions differ*
>> [ 445.27] autocampars: *Log file saved as /var/log/autocampars.log*
>> [ 445.32] init_elphel393: init SATA
>> [ 445.32] init_elphel393: 10389 was not detected: skipping SATA init
>> [ 445.32] init_elphel393: Start GPS and event logger
>> Initializing Exif template: /www/pages/exif.php init noGPS nocompass
>> [ 445.75] init_elphel393: /var/volatile/state already exists
>> [ 445.75] init_elphel393: *DONE, log file: /var/log/init_elphel393.log*
>>
>>
>> This is the output from init_elphel393.py when only the 14 Mpix sensor
>> is connected:
>> [ 45.92] init_elphel393: Fan on
>> [ 45.93] init_elphel393: Initialize USB hub
>> [ 45.94] init_elphel393: 10389 was not detected: skipping USB hub init
>> [ 45.94] init_elphel393: init_elphel393.py: ip = 192.168.0.9, mask =
>> 255.255.255.0
>> [ 45.95] init_elphel393: init_elphel393.py: imgsrv
>> Set port number: 2323
>> Set port number: 2324
>> Set port number: 2325
>> Set port number: 2326
>> [ 46.34] init_elphel393: init_elphel393.py: auto exposure daemon
>> autoexposure#0 started, daemon_bit=0x0, debug=0x1
>> autoexposure#1 started, daemon_bit=0x0, debug=0x1
>> autoexposure#2 started, daemon_bit=0x0, debug=0x1
>> autoexposure.c:141:main: autoexposure#2: drivers initialized
>> autoexposure.c:146:main: autoexposure#2 started daemon_bit=0x0, debug=0x1
>> autoexposure.c:154:main: autoexposure#2 this_frame = 0xe2
>> autoexposure.c:157:main: frame 14: autoexposure#2 this_frame = 0xe2
>> autoexposure#3 started, daemon_bit=0x0, debug=0x1
>> [ 46.58] autocampars: Processing camera state: INITIALIZED
>> [ 46.63] autocampars: Active sensor ports: 2 master_port = 2
>> [ 46.66] autocampars: Sensors map read from the sysfs: [none, none,
>> none, none],[none, none, none, none],[mt9p006, none, none, none],[none,
>> none, none, none]
>> [ 46.71] autocampars: get_application_mode()->4369
>> [ 46.76] autocampars: Detecting sensors for MT9P006
>> [ 46.79] autocampars: Got --init command for already initialized
>> camera, trying to re-initialize
>> [ 46.81] autocampars: Current frame on master port =230, sleeping to
>> give daemons a chance
>> [ 51.84] autocampars: Current frame on master port =280, waking up,
>> daemons should be dead already
>> [ 51.87] autocampars: after reset - current frame on master port =281
>> [ 51.89] autocampars: Reset camera state to BITSTREAM
>> [ 51.97] autocampars: ports:2
>> [ 52.02] autocampars: Started detection for sensor port 2
>> [ 52.05] autocampars: *System FPGA version: 0x039300da*
>> [ 52.07] autocampars: *Sensor interface type: PAR12*
>> [ 52.15] autocampars: *Detected sensors: [none, none, none,
>> none],[none, none, none, none],[mt9p006, none, none, none],[none, none,
>> none, none]*
>> [ 52.17] autocampars: Reached state: SENSORS_DETECTED
>> [ 52.43] autocampars: Disabling sensor port 0
>> [ 52.45] autocampars: Disabling sensor port 1
>> [ 52.48] autocampars: Disabling sensor port 3
>> [ 52.66] autocampars: Frames: -1, -1, 0, -1
>> [ 52.68] autocampars: Reached state: SENSORS_SYNCHRONIZED
>> [ 52.71] autocampars: ports:2
>> [ 52.76] autocampars: autocampars.php parsed configuration file
>> /etc/elphel393/autocampars2.xml.
>> [ 52.84] autocampars: init_cameras() start:
>> camera_state=SENSORS_SYNCHRONIZED
>> [ 52.89] autocampars: Collected gammas == Array
>> (
>> [2617] => 1
>> )
>>
>> [ 52.95] autocampars: port 2 setting @1 init exposure: EXPOS= 1000
>> [ 53.05] autocampars: port 2 setting @8 restoring exposure: EXPOS=
>> 10000
>> [ 53.08] autocampars: will need to skip local 7 frames
>> [ 53.10] autocampars: Reached state PARAMETERS_PRESET
>> [ 53.13] autocampars: Skipping 7 frames
>> [ 53.15] autocampars: Frame delay = 0.1 s
>> aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 7
>> (0x7) are not available. this_frame=0x8, now=0x8
>> autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to
>> errors, skipping a frame
>> aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 8
>> (0x8) are not available. this_frame=0x9, now=0x9
>> autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to
>> errors, skipping a frame
>> [ 54.62] autocampars: *Started camera in periodic self-triggered mode,
>> period = 0.1 s*
>> [ 54.65] autocampars: Reached state PARAMETERS_PRESET
>> [ 54.68] autocampars: Reached state INITIALIZED
>> [ 54.70] autocampars: Sensors on ports: 2 were successfully initialized
>> aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 9
>> (0x9) are not available. this_frame=0xa, now=0xa
>> autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to
>> errors, skipping a frame
>> [ 54.73] autocampars: *INITIALIZED*
>> [ 54.75] autocampars: *Log file saved as /var/log/autocampars.log*
>> [ 54.81] init_elphel393: init SATA
>> aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 10
>> (0xa) are not available. this_frame=0xb, now=0xb
>> autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to
>> errors, skipping a frame
>> [ 54.81] init_elphel393: 10389 was not detected: skipping SATA init
>> [ 54.81] init_elphel393: Start GPS and event logger
>> aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 11
>> (0xb) are not available. this_frame=0xc, now=0xc
>> autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to
>> errors, skipping a frame
>> Initializing Exif template: /www/pages/exif.php init noGPS nocompass
>> [ 55.24] init_elphel393: /var/volatile/state already exists
>> [ 55.24] init_elphel393: *DONE, log file: /var/log/init_elphel393.log*
>>
>> Any assistance in resolving this would be greatly appreciated.
>>
>>
>> Kind regards,
>>
>> *Richard Rigby*
>> Software Developer
>>
>>
>> www.redzone.com
>>
>> Ph: +64 9 479 9901
>>
>> Fax: +64 9 479 9904
>>
>>
>> 13 Tarndale Grove • Albany • Auckland 0632 • New Zealand
>> <https://maps.google.com/?q=13+Tarndale+Grove+%E2%80%A2+Albany+%E2%80%A2+Auckland+0632+%E2%80%A2+New+Zealand&entry=gmail&source=g>
>>
>>
>>
>>
>>
>> _______________________________________________
>> Support-list mailing list
>> Support-list at support.elphel.com
>> http://support.elphel.com/mailman/listinfo/support-list_supp
>> ort.elphel.com
>>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://support.elphel.com/pipermail/support-list_support.elphel.com/attachments/20180226/b09f982d/attachment-0001.html>
More information about the Support-list
mailing list