[Elphel-support] Fwd: 14Mpix sensor not detected
Andrey Filippov
andrey at elphel.com
Fri Feb 23 10:23:19 PST 2018
== == == == == == Forwarded message == == == == == ==
>From : Richard Rigby<rrigby at redzone.com>
To : <support-list at elphel.com>
Date : Thu, 22 Feb 2018 18:28:08 -0800
Subject : 14Mpix sensor not detected
== == == == == == Forwarded message == == == == == ==
Hello,
I have a 393 board as well as one 5 Mpix sensor and one 14 Mpix sensor. However only the 5Mpix sensor is working.
I am using the web interface to view the camera.
I have tried to run the init_elphel393.py script for both sensors and it looks to me that the 14 Mpix sensor cannot be detected.
This is the output from init_elphel393.py when only the 14 Mpix sensor is connected:
[ 443.35] init_elphel393: Fan on
[ 443.36] init_elphel393: Initialize USB hub
[ 443.37] init_elphel393: 10389 was not detected: skipping USB hub init
[ 443.37] init_elphel393: init_elphel393.py: ip = 192.168.0.9, mask = 255.255.255.0
[ 443.38] init_elphel393: init_elphel393.py: imgsrv
Set port number: 2323
Set port number: 2324
Set port number: 2325
Set port number: 2326
[ 443.77] init_elphel393: init_elphel393.py: auto exposure daemon
autoexposure#0 started, daemon_bit=0x0, debug=0x1
autoexposure#1 started, daemon_bit=0x0, debug=0x1
autoexposure#2 started, daemon_bit=0x0, debug=0x1
autoexposure#3 started, daemon_bit=0x0, debug=0x1
[ 443.99] autocampars: Processing camera state: INITIALIZED
[ 444.05] autocampars: Active sensor ports: master_port = -1
[ 444.07] autocampars: Sensors map read from the sysfs: [none, none, none, none],[none, none, none, none],[none, none, none, none],[none, none, none, none]
[ 444.12] autocampars: get_application_mode()->4369
[ 444.17] autocampars: Detecting sensors for MT9P006
[ 444.20] autocampars: Got --init command for already initialized camera, trying to re-initialize
[ 444.22] autocampars: after reset - current frame on master port =
[ 444.25] autocampars: Reset camera state to BITSTREAM
[ 444.33] autocampars: ports:
[ 444.35] autocampars: System FPGA version: 0x039300da
[ 444.38] autocampars: Sensor interface type: PAR12
[ 444.45] autocampars: Detected sensors: [none, none, none, none],[none, none, none, none],[none, none, none, none],[none, none, none, none]
[ 444.48] autocampars: Reached state: SENSORS_DETECTED
[ 444.53] autocampars: Disabling sensor port 0
[ 444.56] autocampars: Disabling sensor port 1
[ 444.58] autocampars: Disabling sensor port 2
[ 444.61] autocampars: Disabling sensor port 3
[ 444.69] autocampars: Frames: -1, -1, -1, -1
[ 444.71] autocampars: Reached state: SENSORS_SYNCHRONIZED
[ 444.74] autocampars: ports:
[ 444.81] autocampars: init_cameras() start: camera_state=SENSORS_SYNCHRONIZED
[ 444.86] autocampars: Collected gammas == Array
(
)
[ 444.89] autocampars: will need to skip local frames
[ 444.92] autocampars: Reached state PARAMETERS_PRESET
[ 444.94] autocampars: Skipping frames
[ 444.97] autocampars: Frame delay = 0 s
[ 445.02] autocampars: Remaining trigger parameters:
Warning: array_key_exists() expects parameter 2 to be array, null given in /usr/bin/autocampars.php on line 1074
Warning: array_key_exists() expects parameter 2 to be array, null given in /usr/bin/autocampars.php on line 1085
Warning: array_key_exists() expects parameter 2 to be array, null given in /usr/bin/autocampars.php on line 1086
Warning: array_key_exists() expects parameter 2 to be array, null given in /usr/bin/autocampars.php on line 1091
Warning: elphel_set_P_arr() expects parameter 2 to be array, null given in /usr/bin/autocampars.php on line 1095
[ 445.09] autocampars: Skipping more frames
[ 445.14] autocampars: Reached state PARAMETERS_PRESET
[ 445.17] autocampars: Reached state INITIALIZED
[ 445.20] autocampars: Sensors on ports: were successfully initialized
[ 445.22] autocampars: INITIALIZED
[ 445.25] autocampars: revisions differ
[ 445.27] autocampars: Log file saved as /var/log/autocampars.log
[ 445.32] init_elphel393: init SATA
[ 445.32] init_elphel393: 10389 was not detected: skipping SATA init
[ 445.32] init_elphel393: Start GPS and event logger
Initializing Exif template: /www/pages/exif.php init noGPS nocompass
[ 445.75] init_elphel393: /var/volatile/state already exists
[ 445.75] init_elphel393: DONE, log file: /var/log/init_elphel393.log
This is the output from init_elphel393.py when only the 14 Mpix sensor is connected:
[ 45.92] init_elphel393: Fan on
[ 45.93] init_elphel393: Initialize USB hub
[ 45.94] init_elphel393: 10389 was not detected: skipping USB hub init
[ 45.94] init_elphel393: init_elphel393.py: ip = 192.168.0.9, mask = 255.255.255.0
[ 45.95] init_elphel393: init_elphel393.py: imgsrv
Set port number: 2323
Set port number: 2324
Set port number: 2325
Set port number: 2326
[ 46.34] init_elphel393: init_elphel393.py: auto exposure daemon
autoexposure#0 started, daemon_bit=0x0, debug=0x1
autoexposure#1 started, daemon_bit=0x0, debug=0x1
autoexposure#2 started, daemon_bit=0x0, debug=0x1
autoexposure.c:141:main: autoexposure#2: drivers initialized
autoexposure.c:146:main: autoexposure#2 started daemon_bit=0x0, debug=0x1
autoexposure.c:154:main: autoexposure#2 this_frame = 0xe2
autoexposure.c:157:main: frame 14: autoexposure#2 this_frame = 0xe2
autoexposure#3 started, daemon_bit=0x0, debug=0x1
[ 46.58] autocampars: Processing camera state: INITIALIZED
[ 46.63] autocampars: Active sensor ports: 2 master_port = 2
[ 46.66] autocampars: Sensors map read from the sysfs: [none, none, none, none],[none, none, none, none],[mt9p006, none, none, none],[none, none, none, none]
[ 46.71] autocampars: get_application_mode()->4369
[ 46.76] autocampars: Detecting sensors for MT9P006
[ 46.79] autocampars: Got --init command for already initialized camera, trying to re-initialize
[ 46.81] autocampars: Current frame on master port =230, sleeping to give daemons a chance
[ 51.84] autocampars: Current frame on master port =280, waking up, daemons should be dead already
[ 51.87] autocampars: after reset - current frame on master port =281
[ 51.89] autocampars: Reset camera state to BITSTREAM
[ 51.97] autocampars: ports:2
[ 52.02] autocampars: Started detection for sensor port 2
[ 52.05] autocampars: System FPGA version: 0x039300da
[ 52.07] autocampars: Sensor interface type: PAR12
[ 52.15] autocampars: Detected sensors: [none, none, none, none],[none, none, none, none],[mt9p006, none, none, none],[none, none, none, none]
[ 52.17] autocampars: Reached state: SENSORS_DETECTED
[ 52.43] autocampars: Disabling sensor port 0
[ 52.45] autocampars: Disabling sensor port 1
[ 52.48] autocampars: Disabling sensor port 3
[ 52.66] autocampars: Frames: -1, -1, 0, -1
[ 52.68] autocampars: Reached state: SENSORS_SYNCHRONIZED
[ 52.71] autocampars: ports:2
[ 52.76] autocampars: autocampars.php parsed configuration file /etc/elphel393/autocampars2.xml.
[ 52.84] autocampars: init_cameras() start: camera_state=SENSORS_SYNCHRONIZED
[ 52.89] autocampars: Collected gammas == Array
(
[2617] => 1
)
[ 52.95] autocampars: port 2 setting @1 init exposure: EXPOS= 1000
[ 53.05] autocampars: port 2 setting @8 restoring exposure: EXPOS= 10000
[ 53.08] autocampars: will need to skip local 7 frames
[ 53.10] autocampars: Reached state PARAMETERS_PRESET
[ 53.13] autocampars: Skipping 7 frames
[ 53.15] autocampars: Frame delay = 0.1 s
aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 7 (0x7) are not available. this_frame=0x8, now=0x8
autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to errors, skipping a frame
aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 8 (0x8) are not available. this_frame=0x9, now=0x9
autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to errors, skipping a frame
[ 54.62] autocampars: Started camera in periodic self-triggered mode, period = 0.1 s
[ 54.65] autocampars: Reached state PARAMETERS_PRESET
[ 54.68] autocampars: Reached state INITIALIZED
[ 54.70] autocampars: Sensors on ports: 2 were successfully initialized
aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 9 (0x9) are not available. this_frame=0xa, now=0xa
autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to errors, skipping a frame
[ 54.73] autocampars: INITIALIZED
[ 54.75] autocampars: Log file saved as /var/log/autocampars.log
[ 54.81] init_elphel393: init SATA
aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 10 (0xa) are not available. this_frame=0xb, now=0xb
autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to errors, skipping a frame
[ 54.81] init_elphel393: 10389 was not detected: skipping SATA init
[ 54.81] init_elphel393: Start GPS and event logger
aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 11 (0xb) are not available. this_frame=0xc, now=0xc
autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to errors, skipping a frame
Initializing Exif template: /www/pages/exif.php init noGPS nocompass
[ 55.24] init_elphel393: /var/volatile/state already exists
[ 55.24] init_elphel393: DONE, log file: /var/log/init_elphel393.log
Any assistance in resolving this would be greatly appreciated.
Kind regards,
Richard Rigby
Software Developer
www.redzone.com
Ph: +64 9 479 9901
Fax: +64 9 479 9904
13 Tarndale Grove • Albany • Auckland 0632 • New Zealand
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://support.elphel.com/pipermail/support-list_support.elphel.com/attachments/20180223/4fcc4978/attachment-0001.html>
More information about the Support-list
mailing list