[Elphel-support] 10338 board

[Adam Gobi]

Thanks for your reply Andrey, but I couldn't see what you were referring
too.  Instead, I've attached a picture to remove any potential ambiguousness
from my original question of left, or right.

Thanks,
ag.

On 16 March 2011 02:01, Andrey Filippov <support-list at support.elphel.com>wrote:

> Adam,
>
> There is +3.3 V power near one end (pins 3,4) connected together. You
> should be able to see that on the board ("left" and "right" may be ambiguous
> here).
>
> Andrey
>
>
> On Tue, Mar 15, 2011 at 4:22 AM, Adam Gobi <adam.gobi at acheron.com.au>wrote:
>
>> Thanks Andrey... so if you're looking at the back of the board where the
>> connector is, is J1-1 on the left side, or right side of the cable?
>>
>> ag.
>>
>>
>> On 15 March 2011 14:16, Andrey Filippov <support-list at support.elphel.com>wrote:
>>
>>> Adam,
>>>
>>> Older sensors we used were 10 (not 12) bit, but they required 3.3V analog
>>> power supply voltage. For them we used switching 3.3V->5.0V converter, then
>>> linear regulator back to 3.3V. To reduce possible interference from the
>>> switching dc-dc converter we synchronized it it to the sensor frames.
>>> 5MPix sensor uses lower power supply that can be linear regulated from
>>> "dirty" 3.3V, so these 2 lines where used as extra data bits. When used in
>>> 323 and 363 cameras more control signal were reassigned to data bits so the
>>> data bus in that case is 14 bit wide, using the same 10313 system boards in
>>> the 323 camera and 10353 in the 363.
>>>
>>> Andrey
>>>
>>> On Mon, Mar 14, 2011 at 7:59 PM, Adam Gobi <adam.gobi at acheron.com.au>wrote:
>>>
>>>> Thanks Andrey, looks good.  Also, I was just curious about why you have
>>>> the Dout[0] and Dout[1] pins separate from the rest of the sensor data
>>>> output pins, and named CNVSYNC and CNVCLK?
>>>>
>>>> Thanks,
>>>> ag.
>>>>
>>>>
>>>> On 15 March 2011 12:32, Andrey Filippov <
>>>> support-list at support.elphel.com> wrote:
>>>>
>>>>> Adam, yes, the pinout is the same. The circuit diagram of the 10338D is
>>>>> on the page http://wiki.elphel.com/index.php?title=10338D , we just
>>>>> did not update photos there.
>>>>>
>>>>> Andrey
>>>>>
>>>>>
>>>>> On Mon, Mar 14, 2011 at 7:13 PM, Adam Gobi <adam.gobi at acheron.com.au>wrote:
>>>>>
>>>>>> Hi Andrey,
>>>>>>
>>>>>> Just looking at at the cable pinouts in 10338a.pdf, which appears to
>>>>>> be for revision 'A'.  Do they correspond with the 10338 revision 'D' board
>>>>>> that came with my 353 camera, including the 3.3V supply voltage requirement?
>>>>>>
>>>>>> Thanks,
>>>>>> ag.
>>>>>>
>>>>>>
>>>>>> --
>>>>>> Adam Gobi
>>>>>> Lead Engineer - Imaging
>>>>>> Acheron Project Pty Ltd
>>>>>> Leichhardt, NSW, Australia
>>>>>> e: gobi at acheron.com.au <adam.gobi at acheron.com.au>
>>>>>> v: +61 451 951 323
>>>>>> f: +61 2 9571 5575
>>>>>>
>>>>>>
>>>>>
>>>>
>>>>
>>>> --
>>>> Adam Gobi
>>>> Lead Engineer - Imaging
>>>> Acheron Project Pty Ltd
>>>> Leichhardt, NSW, Australia
>>>> e: gobi at acheron.com.au <adam.gobi at acheron.com.au>
>>>> v: +61 451 951 323
>>>> f: +61 2 9571 5575
>>>>
>>>>
>>>> _______________________________________________
>>>> Support-list mailing list
>>>> Support-list at support.elphel.com
>>>>
>>>> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
>>>>
>>>>
>>>
>>
>>
>> --
>> Adam Gobi
>> Lead Engineer - Imaging
>> Acheron Project Pty Ltd
>> Leichhardt, NSW, Australia
>> e: gobi at acheron.com.au <adam.gobi at acheron.com.au>
>> v: +61 451 951 323
>> f: +61 2 9571 5575
>>
>>
>> _______________________________________________
>> Support-list mailing list
>> Support-list at support.elphel.com
>> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
>>
>>
>


-- 
Adam Gobi
Lead Engineer - Imaging
Acheron Project Pty Ltd
Leichhardt, NSW, Australia
e: gobi at acheron.com.au <adam.gobi at acheron.com.au>
v: +61 451 951 323
f: +61 2 9571 5575
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://support.elphel.com/pipermail/support-list_support.elphel.com/attachments/20110316/77d95901/attachment-0002.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: board.JPG
Type: image/jpeg
Size: 53876 bytes
Desc: not available
URL: <http://support.elphel.com/pipermail/support-list_support.elphel.com/attachments/20110316/77d95901/attachment.jpe>