[Elphel-support] 10338 board

[Andrey Filippov]

Adam,

There is +3.3 V power near one end (pins 3,4) connected together. You should
be able to see that on the board ("left" and "right" may be ambiguous here).

Andrey

On Tue, Mar 15, 2011 at 4:22 AM, Adam Gobi <adam.gobi at acheron.com.au> wrote:

> Thanks Andrey... so if you're looking at the back of the board where the
> connector is, is J1-1 on the left side, or right side of the cable?
>
> ag.
>
>
> On 15 March 2011 14:16, Andrey Filippov <support-list at support.elphel.com>wrote:
>
>> Adam,
>>
>> Older sensors we used were 10 (not 12) bit, but they required 3.3V analog
>> power supply voltage. For them we used switching 3.3V->5.0V converter, then
>> linear regulator back to 3.3V. To reduce possible interference from the
>> switching dc-dc converter we synchronized it it to the sensor frames.
>> 5MPix sensor uses lower power supply that can be linear regulated from
>> "dirty" 3.3V, so these 2 lines where used as extra data bits. When used in
>> 323 and 363 cameras more control signal were reassigned to data bits so the
>> data bus in that case is 14 bit wide, using the same 10313 system boards in
>> the 323 camera and 10353 in the 363.
>>
>> Andrey
>>
>> On Mon, Mar 14, 2011 at 7:59 PM, Adam Gobi <adam.gobi at acheron.com.au>wrote:
>>
>>> Thanks Andrey, looks good.  Also, I was just curious about why you have
>>> the Dout[0] and Dout[1] pins separate from the rest of the sensor data
>>> output pins, and named CNVSYNC and CNVCLK?
>>>
>>> Thanks,
>>> ag.
>>>
>>>
>>> On 15 March 2011 12:32, Andrey Filippov <support-list at support.elphel.com
>>> > wrote:
>>>
>>>> Adam, yes, the pinout is the same. The circuit diagram of the 10338D is
>>>> on the page http://wiki.elphel.com/index.php?title=10338D , we just did
>>>> not update photos there.
>>>>
>>>> Andrey
>>>>
>>>>
>>>> On Mon, Mar 14, 2011 at 7:13 PM, Adam Gobi <adam.gobi at acheron.com.au>wrote:
>>>>
>>>>> Hi Andrey,
>>>>>
>>>>> Just looking at at the cable pinouts in 10338a.pdf, which appears to be
>>>>> for revision 'A'.  Do they correspond with the 10338 revision 'D' board that
>>>>> came with my 353 camera, including the 3.3V supply voltage requirement?
>>>>>
>>>>> Thanks,
>>>>> ag.
>>>>>
>>>>>
>>>>> --
>>>>> Adam Gobi
>>>>> Lead Engineer - Imaging
>>>>> Acheron Project Pty Ltd
>>>>> Leichhardt, NSW, Australia
>>>>> e: gobi at acheron.com.au <adam.gobi at acheron.com.au>
>>>>> v: +61 451 951 323
>>>>> f: +61 2 9571 5575
>>>>>
>>>>>
>>>>
>>>
>>>
>>> --
>>> Adam Gobi
>>> Lead Engineer - Imaging
>>> Acheron Project Pty Ltd
>>> Leichhardt, NSW, Australia
>>> e: gobi at acheron.com.au <adam.gobi at acheron.com.au>
>>> v: +61 451 951 323
>>> f: +61 2 9571 5575
>>>
>>>
>>> _______________________________________________
>>> Support-list mailing list
>>> Support-list at support.elphel.com
>>>
>>> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
>>>
>>>
>>
>
>
> --
> Adam Gobi
> Lead Engineer - Imaging
> Acheron Project Pty Ltd
> Leichhardt, NSW, Australia
> e: gobi at acheron.com.au <adam.gobi at acheron.com.au>
> v: +61 451 951 323
> f: +61 2 9571 5575
>
>
> _______________________________________________
> Support-list mailing list
> Support-list at support.elphel.com
> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://support.elphel.com/pipermail/support-list_support.elphel.com/attachments/20110315/eac3237b/attachment-0002.html>