[Elphel-support] 10393 for 3 KAI11002 at 4.8 fps(30mhz)

[Yakov]

Ok. You can't develop software. Pity. I will try to find someone to
outsource software development. I just need software for one machine.
Global shutter and CCD's much much better. For book scanning. Why
global shutter. Because camera moving up and down. 1500 times in one
hour. Check Treventus.
CCD's because of the color. CMOS have issues with blue channel.

Regards,
Iakov(Yakov) Petrov.

On Sun, Jul 3, 2016 at 7:59 AM, support-list
<support-list at support.elphel.com> wrote:
> Yakov,
>
> we are too busy with the current projects so we only can help with some
> consultations, not do the actual design.
>
> And why do you think global shutter is better for book scanning? Rolling
> shutter ones provide better S/N for the same pixel size
>
> Andrey
>
> ---- On Sat, 02 Jul 2016 19:26:47 -0700 Yakov<queilasha at gmail.com> wrote
> ----
>
> Yeah. But these sensors are CCD and have global shutter. Ideal for
> book scanning in industrial scale.
> How much will be to write such a firmware for 10393? Do you have
> firmware for 10353? Maybe some other sensor boards can be developed
> based on 25MP CMOS global shutter sensors?
>
> Regards,
> Iakov(Yakov) Petrov.
>
> On Sun, Jul 3, 2016 at 7:21 AM, support-list
> <support-list at support.elphel.com> wrote:
>> Yakov,
>>
>> Just one will definitely be enough, but there is no code to run these
>> sensor
>> boards. And as these sensors are rather old it may be easier to just use
>> NC323 than to develop firmware fro the 393 to run these sensors.
>>
>> Andrey
>>
>> ---- On Sat, 02 Jul 2016 19:07:02 -0700 Yakov<queilasha at gmail.com> wrote
>> ----
>>
>> Hello Andrey. How many 10393 CPU boards I need to run 3 KAI11002 at
>> 4.8 fps at 30mhz?
>>
>> Regards,
>> Iakov(Yakov) Petrov.
>>
>> On Mon, Aug 24, 2015 at 11:24 PM, support-list
>> <support-list at support.elphel.com> wrote:
>>> Hello Yakov,
>>>
>>> The 10393 boards (main boards of the NC393 cameras) are
>>> hardware-compatible
>>> with the older sensor boards. The new system board has 4 identical ports
>>> each with the pinout compatible with 10313, 10333 and 10353 boards. The
>>> new
>>> camera will also support modern serial sensor interfaces, but the bakward
>>> compatibility will be 100% preserved - with the flexibility of FPGA it is
>>> not that difficult.
>>>
>>> I just finished simulation of the camera FPGA (comparing against 10353
>>> with
>>> the same sensor data) and now I'm starting to test it on the actual
>>> hardware
>>>
>>>
>>> Andrey
>>>
>>> Hello. Will NC393 boards will be backward compatible with 323 hardware?
>>>
>>> Best regards,
>>> Yakov Petrov.
>>>
>>
>> _______________________________________________
>> Support-list mailing list
>> Support-list at support.elphel.com
>> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
>>
>>
>>
>
> _______________________________________________
> Support-list mailing list
> Support-list at support.elphel.com
> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
>
>
>