[Elphel-support] Physically rotate SFE 180 degrees

[Nathan Clark]

Fantastic!

As it turns out, I have previously used this feature-
But my assumption was that this merely flips the image, rather than
changing the actual readout direction!

Thanks for your help and continued support!

-Nathan


On Mon, Dec 5, 2011 at 8:41 PM, Andrey Filippov <
support-list at support.elphel.com> wrote:

> Nathan,
>
> it can be done in multiple ways. You can try it in the camera GUI, you
> also can set default configuration with http://192.168.0.9/autocampars.php- there you just put the checkboxes on the groups of parameters to
> view/edit (in that case it will be the second line:
> Window of Interest (WOI), then open link View/Edit current, after editing
> you may save the settings to be used  automatically after camera will boot
> next time.
>
> You can also control these parameter alone with the following URL:
>
> http://192.168.0.9/parsedit.php?FLIPH&FLIPV
>
> When opening such (or similar)control page, you may hover the mouse
> pointer over the parameter name - the "tooltip" will show what it means.
>
> Andrey
>
>
> On Mon, Dec 5, 2011 at 2:28 AM, Nathan Clark <nathan at nathanclark.com.au>wrote:
>
>> Andrey,
>>
>> Sorry to bother you again-
>> Would you mind pointing me in the direction of where to adjust this
>> parameter?
>> I couldn't seem to find it on the wiki.
>>
>> Kind regards,
>> Nathan
>>
>> On Mon, Dec 5, 2011 at 8:22 PM, Nathan Clark <nathan at nathanclark.com.au>wrote:
>>
>>> Andrey,
>>>
>>> I didn't realize this could be done,
>>> thanks so much, that's a great solution!
>>>
>>> Nathan
>>>
>>>
>>> On Mon, Dec 5, 2011 at 8:09 PM, Andrey Filippov <
>>> support-list at support.elphel.com> wrote:
>>>
>>>> Hi Nathan,
>>>>
>>>> Why do you need to rotate the SFE by 180? You can just select the
>>>> direction of the readout, so all scanned lines will match. In our
>>>> multi-sensor cameras we do not care much about such rotation, orient SFE in
>>>> one of the two ways depending on the mechanical convenience.
>>>>
>>>> Andrey
>>>>
>>>> On Mon, Dec 5, 2011 at 1:35 AM, Nathan Clark <nathan at nathanclark.com.au
>>>> > wrote:
>>>>
>>>>> Hi Elphel,
>>>>>
>>>>> I'm hoping to use one of my cameras "upside down" in the new rig I am
>>>>> designing.
>>>>> But I would like to rotate the SFE so that both sensors are the same
>>>>> orientation.
>>>>>
>>>>> Unfortunately, the flex cable that connects to the SFE is too short to
>>>>> support this rotation.
>>>>>
>>>>> Can you offer any ideas for how this might be achieved?
>>>>> Perhaps there is a "crossed" flex cable I could use instead?
>>>>>
>>>>> Alternatively (and perhaps a better option)
>>>>> Are you able to provide a top case that has a tripod mounting socket,
>>>>> just like the bottom case has now?
>>>>> This would be the ultimate solution, as it would allow the camera to
>>>>> be oriented in either configurations.
>>>>>
>>>>> --Nathan
>>>>>
>>>>> _______________________________________________
>>>>> Support-list mailing list
>>>>> Support-list at support.elphel.com
>>>>>
>>>>> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
>>>>>
>>>>>
>>>>
>>>
>>
>> _______________________________________________
>> Support-list mailing list
>> Support-list at support.elphel.com
>> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
>>
>>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://support.elphel.com/pipermail/support-list_support.elphel.com/attachments/20111206/a794943d/attachment-0002.html>