[Elphel-support] problem with stereo setup

Fri Aug 6 09:36:19 PDT 2010

P.S. just a reminder:
on the 10359:
to J2-J4 cables go foil contacts down
to J1 - foil up

On 6 August 2010 10:21, Oleg K Dzhimiev <oleg at elphel.com> wrote:

> Dear Jorick,
>
> 1. Check the sensors - unscrew the middle cover - attach each cable
> directly to the camera. To see if the at least work.
>
> 2. Probably just reattaching the cables (one of the sensors should be
> connected to J2 (it's the nearest to the 10353-10359 port J1)) to 10359 will
> help if the sensors are detected then you'll get lines in the log like:
>
>> Found MT9P001 2592x1944 sensor on 10359A port 1, chip ID=1801
>> Found MT9P001 2592x1944 sensor on 10359A port 2, chip ID=1801
>>
>
> What is strange is that at least one of the sensors was detected in your
> first log but the behavior was as if the TRIG=4.
>
> Best regards,
> Oleg
>
>
> On 6 August 2010 04:14, Jorick Astrego <jorick at netbulae.com> wrote:
>
>>  Dear Oleg/Andrey,
>>
>> We reverted back to the older firmware 8.0.8.25 as Andrey suggested. One
>> of our developers thought the latest CVS version would be better.
>>
>> After reflashing I tried:
>>
>> delete /etc/autocampars.xml, disconnect 10359 and rebooting
>>
>> But still no sensors detected.
>>
>> When I check "ftp://192.168.2.199/etc/autocampars.xml" the TRIG parameter
>> is set to 0, I've attached it to this email
>>
>> And when I check the sensors, I get:
>>
>> [root at Elphel353 /root]825# fpcf -i2cr16 4c00
>> read failed, returned -1, expected - 2
>> [root at Elphel353 /root]825# fpcf -i2cr16 4a00
>> read failed, returned -1, expected - 2
>> [root at Elphel353 /root]825# fpcf -i2cr16 4e00
>> read failed, returned -1, expected - 2
>>
>> After that I tried:
>>
>> [root at Elphel353 /root]825# fpcf -X 1
>> Clock 1 is OFF
>> [root at Elphel353 /root]825# fpcf -X 1 96
>> Set clock 1 to 9.600000e+01MHz
>> [root at Elphel353 /root]825# fpcf -X 1
>> Clock 1 is set to 9.600000e+01MHz
>>
>> This is is "/var/log/messages
>>
>> Jan  1 00:00:43 Elphel353 kernel: initSequencers:resetting both sequencers
>> Jan  1 00:00:43 Elphel353 kernel: Initializing DMA registers for EXTDMA3 -
>> sensor clock set to 20000000
>> Jan  1 00:00:43 Elphel353 kernel: 10359 bitstream version =0x0359a04c
>> Jan  1 00:00:43 Elphel353 kernel: 10353 sensor clock set to 96000000
>> Jan  1 00:00:43 Elphel353 kernel: 10359A sensor clock set to 96000000
>> Jan  1 00:00:43 Elphel353 kernel: removing MRST from the sensor
>> Jan  1 00:00:43 Elphel353 kernel: removing MRST from the sensor
>> Jan  1 00:00:43 Elphel353 kernel: trying MT9P001
>> Jan  1 00:00:43 Elphel353 kernel: trying other MT9X001
>> Jan  1 00:00:43 Elphel353 kernel: sensor power set low^M
>> Jan  1 00:00:43 Elphel353 kernel:  will set to 0x41^M
>> Jan  1 00:00:43 Elphel353 kernel: will set to 0x30^M
>> Jan  1 00:00:43 Elphel353 kernel: will set to 0x28^M
>> Jan  1 00:00:43 Elphel353 kernel: will set to 0x24^M
>> Jan  1 00:00:43 Elphel353 kernel: will set to 0x22^M
>> Jan  1 00:00:43 Elphel353 kernel: .. full^M
>> Jan  1 00:00:43 Elphel353 kernel: Inverted MRST
>> Jan  1 00:00:43 Elphel353 kernel: trying MT9X001
>> Jan  1 00:00:43 Elphel353 kernel: No image sensor found^M
>> Jan  1 00:00:43 Elphel353 kernel:
>> arch/cris/arch-v32/drivers/elphel/multisensor.c:1188:multisensor_pgm_sensorphase
>> WARNING: ((thispars->pars[P_CLK_SENSOR] == prevpars->pars[P_CLK_SENSOR]))
>> but multi_phases_initialized is not yet set ********
>> Jan  1 00:00:43 Elphel353 kernel: Error programming clock 0 fact=0,
>> err=0xffffff00
>> Jan  1 00:00:43 Elphel353 kernel:
>> arch/cris/arch-v32/drivers/elphel/multisensor.c:1226:multisensor_pgm_sensorphase
>> **** ERROR adjusting SDRAM clock phase in
>> arch/cris/arch-v32/drivers/elphel/multisensor.c:1227:multisensor_pgm_sensorphase,
>> result=0xfffffffc
>> Jan  1 00:02:30 Elphel353 ipsetd[725]: Timed out after 120s.
>>
>> And on "http://192.168.2.199/359/10359_controls.html"<http://192.168.2.199/359/10359_controls.html>when I press "read registers" I only get "ffffff" in every field.
>>
>> So there must be something else wrong :-(
>>
>> Regards,
>>
>> Jorick
>>
>>
>> On 08/05/2010 07:15 PM, Oleg K Dzhimiev wrote:
>>
>> Dear Jorick,
>>
>> You probably got my yesterday's letter in spam... If not - have you tried
>> this?
>>
>>   You're probably using almost the latest software. So, the problem is -
>>> the software when detects the 10359 puts the sensors into the triggered mode
>>> - and it needs a sync connection with another camera (we use this in our
>>> panorama camera).
>>>
>>> 1.
>>> The solution is to get "ftp://192.168.2.199/etc/autocampars.xml" and set
>>> the TRIG parameter to 0:
>>> old: 4 //external trigger mode
>>> new: 0 //free run
>>>
>>> Copy it back and in a telnet or ssh session launch:
>>> "/usr/html/autocampars.php --init" or just reboot
>>>
>>> 2.
>>> To check if the sensors were detected in telnet/ssh/phpshell type:
>>> for J2: fpcf -i2cr16 4a00 (result is 0x1801)
>>> for J3: fpcf -i2cr16 4c00 (result is 0x1801)
>>> for J4: fpcf -i2cr16 4e00 (result is 0x1801) (there is no sensor there
>>> but anyway)
>>>
>>>  About "test_inner_10359.php" -
>>
>>  <test name="test_10359">
>>>
>>  <board_id result="ok">10359</board_id>
>>>
>>  -
>>>
>>  <firmware result="fail">
>>>
>>  An old firmware revision or i2c doesn't work, got -1
>>>
>>  </firmware>
>>>
>>  <finish result="fail"/>
>>>
>>  </test>
>>>
>>
>> This can be tested in a telnet/ssh session also:
>> a. "fpcf -X 1" - (shoud be 96MHz) frequency to the 10359. "fpcf -X 1 96"
>> will turn it on if it's off
>> b. If the frequency is on you can read the 10359 registers through
>> http://192.168.2.199/359/10359_controls.html
>>
>> Please modify autocampars.xml first (you can copy the attached one to the
>> camera) and then we will move on.
>>
>> Best regards,
>> Oleg
>>
>> On 5 August 2010 09:18, Jorick Astrego <jorick at netbulae.com> wrote:
>>
>>>  Dear people,
>>>
>>> This week we received an elphel assembled stereo setup (two sensors and
>>> a 10359 plus crossbar) to hook to our elphel 10353 with 10369.
>>>
>>> We are running release 8.0.8.37 from cvs
>>>
>>> The problem is now that we don't receive any image.
>>>
>>> The 10359 looks ok but doesn't read the registers with the button on:
>>>
>>> http://elphel.netbulae.com/index.php?site=camerasetup/setup.php
>>>
>>> I get an error "failed to start"
>>>
>>> In the /var/log/messages I get this info:
>>>
>>> Jan 1 00:00:44 Elphel353 syslogd 1.4.1: restart.
>>> Jan 1 00:00:44 Elphel353 kernel: klogd 1.4.1, log source = /proc/kmsg
>>> started.
>>> Jan 1 00:00:44 Elphel353 kernel: Linux version 2.6.19
>>> (root at tsarcasm-mobile) (gcc version 3.2.1 Axis release R64/1.64) #1 Wed
>>> Aug 4 15:38:13 CEST 2010
>>> Jan 1 00:00:44 Elphel353 kernel: Setting up paging and the MMU.
>>> Jan 1 00:00:44 Elphel353 kernel: Linux/CRISv32 port on ETRAX FS (C)
>>> 2003, 2004 Axis Communications AB
>>> Jan 1 00:00:44 Elphel353 kernel: Built 1 zonelists. Total pages: 8160
>>> Jan 1 00:00:44 Elphel353 kernel: Kernel command line:
>>> root=/dev/mtdblock3 init=/linuxrc rootfstype=jffs2
>>> Jan 1 00:00:44 Elphel353 kernel: PID hash table entries: 256 (order: 8,
>>> 1024 bytes)
>>> Jan 1 00:00:44 Elphel353 kernel: Dentry cache hash table entries: 8192
>>> (order: 2, 32768 bytes)
>>> Jan 1 00:00:44 Elphel353 kernel: Inode-cache hash table entries: 4096
>>> (order: 1, 16384 bytes)
>>> Jan 1 00:00:44 Elphel353 kernel: Memory: 41376k/65536k available (1738k
>>> kernel code, 24160k reserved, 607k data, 72k init)
>>> Jan 1 00:00:44 Elphel353 kernel: Mount-cache hash table entries: 1024
>>> Jan 1 00:00:44 Elphel353 kernel: NET: Registered protocol family 16
>>> Jan 1 00:00:44 Elphel353 kernel: SCSI subsystem initialized
>>> Jan 1 00:00:44 Elphel353 kernel: usbcore: registered new interface
>>> driver usbfs
>>> Jan 1 00:00:44 Elphel353 kernel: usbcore: registered new interface
>>> driver hub
>>> Jan 1 00:00:44 Elphel353 kernel: usbcore: registered new device driver
>>> usb
>>> Jan 1 00:00:44 Elphel353 kernel: NET: Registered protocol family 2
>>> Jan 1 00:00:44 Elphel353 kernel: IP route cache hash table entries: 512
>>> (order: -2, 2048 bytes)
>>> Jan 1 00:00:44 Elphel353 kernel: TCP established hash table entries:
>>> 2048 (order: 0, 8192 bytes)
>>> Jan 1 00:00:44 Elphel353 kernel: TCP bind hash table entries: 1024
>>> (order: -1, 4096 bytes)
>>> Jan 1 00:00:44 Elphel353 kernel: TCP: Hash tables configured
>>> (established 2048 bind 1024)
>>> Jan 1 00:00:44 Elphel353 kernel: TCP reno registered
>>> Jan 1 00:00:44 Elphel353 kernel: Check hardware configuration of Elphel
>>> 353 camera
>>> Jan 1 00:00:44 Elphel353 kernel: Elphel 10349/10369 IO extension board
>>> is present
>>> Jan 1 00:00:44 Elphel353 kernel: fast_timer_init()
>>> Jan 1 00:00:44 Elphel353 kernel: JFFS2 version 2.2. (NAND) (C) 2001-2006
>>> Red Hat, Inc.
>>> Jan 1 00:00:44 Elphel353 kernel: io scheduler noop registered (default)
>>> Jan 1 00:00:44 Elphel353 kernel: Serial: CRISv32 driver $Revision: 1.78
>>> $ <6>ttyS0 at I/O 0xb0026000 (irq = 68) is a CRISv32
>>> Jan 1 00:00:44 Elphel353 kernel: RAMDISK driver initialized: 16 RAM
>>> disks of 4096K size 1024 blocksize
>>> Jan 1 00:00:44 Elphel353 kernel: PPP generic driver version 2.4.2
>>> Jan 1 00:00:44 Elphel353 kernel: ETRAX FS 10/100MBit ethernet v0.01 (c)
>>> 2003 Axis Communications AB
>>> Jan 1 00:00:44 Elphel353 kernel: eth0: changed MAC to 00:40:8C:CD:00:00
>>> Jan 1 00:00:44 Elphel353 kernel: Uniform Multi-Platform E-IDE driver
>>> Revision: 7.00alpha2
>>> Jan 1 00:00:44 Elphel353 kernel: ide: Assuming 50MHz system bus speed
>>> for PIO modes; override with idebus=xx
>>> Jan 1 00:00:44 Elphel353 kernel: ide: ETRAX FS built-in ATA DMA
>>> controller
>>> Jan 1 00:00:44 Elphel353 kernel: cris_ide_init()
>>> Jan 1 00:00:44 Elphel353 kernel: hdb: probing with STATUS(0xca) instead
>>> of ALTSTATUS(0x8a)
>>> Jan 1 00:00:44 Elphel353 kernel: hdb: no response (status = 0xff),
>>> resetting drive
>>> Jan 1 00:00:44 Elphel353 kernel: hdb: no response (status = 0xff)
>>> Jan 1 00:00:44 Elphel353 kernel: Initializing USB Mass Storage driver...
>>> Jan 1 00:00:44 Elphel353 kernel: usbcore: registered new interface
>>> driver usb-storage
>>> Jan 1 00:00:44 Elphel353 kernel: USB Mass Storage support registered.
>>> Jan 1 00:00:44 Elphel353 kernel: usbcore: registered new interface
>>> driver usbserial
>>> Jan 1 00:00:44 Elphel353 kernel: drivers/usb/serial/usb-serial.c: USB
>>> Serial support registered for generic
>>> Jan 1 00:00:44 Elphel353 kernel: usbcore: registered new interface
>>> driver usbserial_generic
>>> Jan 1 00:00:44 Elphel353 kernel: drivers/usb/serial/usb-serial.c: USB
>>> Serial Driver core
>>> Jan 1 00:00:44 Elphel353 kernel: drivers/usb/serial/usb-serial.c: USB
>>> Serial support registered for Belkin / Peracom / GoHubs USB Serial
>>> Adapter
>>> Jan 1 00:00:44 Elphel353 kernel: usbcore: registered new interface
>>> driver belkin
>>> Jan 1 00:00:45 Elphel353 kernel: drivers/usb/serial/belkin_sa.c: USB
>>> Belkin Serial converter driver v1.2
>>> Jan 1 00:00:45 Elphel353 kernel: drivers/usb/serial/usb-serial.c: USB
>>> Serial support registered for cp2101
>>> Jan 1 00:00:45 Elphel353 kernel: usbcore: registered new interface
>>> driver cp2101
>>> Jan 1 00:00:45 Elphel353 kernel: drivers/usb/serial/cp2101.c: Silicon
>>> Labs CP2101/CP2102 RS232 serial adaptor driver v0.07
>>> Jan 1 00:00:45 Elphel353 kernel: drivers/usb/serial/usb-serial.c: USB
>>> Serial support registered for Garmin GPS usb/tty
>>> Jan 1 00:00:45 Elphel353 kernel: usbcore: registered new interface
>>> driver garmin_gps
>>> Jan 1 00:00:45 Elphel353 kernel: drivers/usb/serial/garmin_gps.c: garmin
>>> gps driver v0.28
>>> Jan 1 00:00:45 Elphel353 kernel: drivers/usb/serial/usb-serial.c: USB
>>> Serial support registered for MCT U232
>>> Jan 1 00:00:45 Elphel353 kernel: usbcore: registered new interface
>>> driver mct_u232
>>> Jan 1 00:00:45 Elphel353 kernel: drivers/usb/serial/mct_u232.c: Magic
>>> Control Technology USB-RS232 converter driver z2.0
>>> Jan 1 00:00:45 Elphel353 kernel: drivers/usb/serial/usb-serial.c: USB
>>> Serial support registered for pl2303
>>> Jan 1 00:00:45 Elphel353 kernel: usbcore: registered new interface
>>> driver pl2303
>>> Jan 1 00:00:45 Elphel353 kernel: drivers/usb/serial/pl2303.c: Prolific
>>> PL2303 USB to serial adaptor driver
>>> Jan 1 00:00:45 Elphel353 kernel: ETRAX FS stream co-processor driver
>>> v0.01, (c) 2003 Axis Communications AB
>>> Jan 1 00:00:45 Elphel353 kernel: stream co-processor: init done.
>>> Jan 1 00:00:45 Elphel353 kernel: axisflashmap: ...
>>> Jan 1 00:00:45 Elphel353 kernel: NAND device: Manufacturer ID: 0x20,
>>> Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit)
>>> Jan 1 00:00:45 Elphel353 kernel: Additional Info: ID byte3=0x80,
>>> byte4=0x1d
>>> Jan 1 00:00:45 Elphel353 kernel: Flash is rated 30 ns, modifying
>>> bif_core_rw_grp3: old=0x6300483, new=0x6300001
>>> Jan 1 00:00:45 Elphel353 kernel: NAND 128MiB 3,3V 8-bit: 0x08000000
>>> bytes of NAND flash memory.
>>> Jan 1 00:00:45 Elphel353 kernel: axisflashmap: Set to boot from NAND
>>> flash, making NAND flash primary device.
>>> Jan 1 00:00:45 Elphel353 kernel: axisflashmap: flash read 512 bytes at
>>> 0x00040000, data: 00 b0 05 f0 25 ff ed 9c
>>> Jan 1 00:00:45 Elphel353 kernel: axisflashmap: partition table offset
>>> 10, data: ef be 84 00 a1 0d 00 00
>>> Jan 1 00:00:45 Elphel353 kernel: axisflashmap: Found a valid partition
>>> table at 0xc02fd9ae-0xc02fda3a.
>>> Jan 1 00:00:45 Elphel353 kernel: offset == 0x00040000, size == 0x007C0000
>>> Jan 1 00:00:45 Elphel353 kernel: offset == 0x00800000, size == 0x01800000
>>> Jan 1 00:00:45 Elphel353 kernel: offset == 0x02000000, size == 0x05000000
>>> Jan 1 00:00:45 Elphel353 kernel: offset == 0x07000000, size == 0x00C00000
>>> Jan 1 00:00:45 Elphel353 kernel: Creating 1 MTD partitions on "NAND
>>> 128MiB 3,3V 8-bit":
>>> Jan 1 00:00:45 Elphel353 kernel: 0x00000000-0x08000000 : "main"
>>> Jan 1 00:00:45 Elphel353 kernel: Creating 1 MTD partitions on "NAND
>>> 128MiB 3,3V 8-bit":
>>> Jan 1 00:00:45 Elphel353 kernel: 0x00000000-0x00040000 : "part0"
>>> Jan 1 00:00:45 Elphel353 kernel: Creating 1 MTD partitions on "NAND
>>> 128MiB 3,3V 8-bit":
>>> Jan 1 00:00:45 Elphel353 kernel: 0x00040000-0x00800000 : "part1"
>>> Jan 1 00:00:45 Elphel353 kernel: Creating 1 MTD partitions on "NAND
>>> 128MiB 3,3V 8-bit":
>>> Jan 1 00:00:45 Elphel353 kernel: 0x00800000-0x02000000 : "part2"
>>> Jan 1 00:00:45 Elphel353 kernel: Creating 1 MTD partitions on "NAND
>>> 128MiB 3,3V 8-bit":
>>> Jan 1 00:00:45 Elphel353 kernel: 0x02000000-0x07000000 : "part3"
>>> Jan 1 00:00:45 Elphel353 kernel: Creating 1 MTD partitions on "NAND
>>> 128MiB 3,3V 8-bit":
>>> Jan 1 00:00:45 Elphel353 kernel: 0x07000000-0x07c00000 : "part4"
>>> Jan 1 00:00:45 Elphel353 kernel: ETRAX FS GPIO driver v2.5, (c)
>>> 2003-2006 Axis Communications AB
>>> Jan 1 00:00:45 Elphel353 kernel: Elphel (R) model 353 FPGA (Xilinx (R)
>>> XC3S1200E) configuration driver - 132
>>> Jan 1 00:00:45 Elphel353 kernel: Elphel (R) model 353 system clocks (PLL
>>> frequency synth.) driver - 133
>>> Jan 1 00:00:45 Elphel353 kernel: fpga_control- 129
>>> Jan 1 00:00:45 Elphel353 kernel:
>>> arch/cris/arch-v32/drivers/elphel/framepars.c:384:initGlobalPars
>>> GLOBALPARS(G_DEBUG)=0
>>> Jan 1 00:00:45 Elphel353 kernel:
>>> arch/cris/arch-v32/drivers/elphel/framepars.c:414:initMultiPars
>>> GLOBALPARS(G_MULTI_NUM)=0
>>> Jan 1 00:00:45 Elphel353 kernel: Elphel (R) Model 353 Frame Parameters
>>> device driver - 130
>>> Jan 1 00:00:45 Elphel353 kernel: Elphel FPGA interrupts initialized
>>> Jan 1 00:00:45 Elphel353 kernel: Initializing DMA registers for EXTDMA3
>>> - Elphel (R) Model 353 Camera Driver - 126
>>> Jan 1 00:00:45 Elphel353 kernel: Elphel (R) model 353 i2c character
>>> device driver - 134, 2 channels
>>> Jan 1 00:00:45 Elphel353 kernel: Raw image access driver- 131
>>> Jan 1 00:00:45 Elphel353 kernel: Elphel (R) Model 353 video buffer
>>> device driver- 135
>>> Jan 1 00:00:45 Elphel353 kernel: Elphel (R) model 353 Exif device driver
>>> - 125
>>> Jan 1 00:00:45 Elphel353 kernel: Starting Elphel (R) Model 353 Gamma
>>> Tables device driver - 137
>>> Jan 1 00:00:45 Elphel353 kernel: Elphel (R) Model 353 Gamma Tables
>>> device driver - 137
>>> Jan 1 00:00:45 Elphel353 kernel: Elphel (R) Model 353 Histograms device
>>> driver^M
>>> Jan 1 00:00:45 Elphel353 kernel: TCP cubic registered
>>> Jan 1 00:00:45 Elphel353 kernel: NET: Registered protocol family 1
>>> Jan 1 00:00:45 Elphel353 kernel: NET: Registered protocol family 17
>>> Jan 1 00:00:45 Elphel353 kernel: VFS: Mounted root (jffs2 filesystem)
>>> readonly.
>>> Jan 1 00:00:45 Elphel353 kernel: Freeing unused kernel memory: 72k freed
>>> Jan 1 00:00:45 Elphel353 kernel: Empty flash at 0x00b20a58 ends at
>>> 0x00b21000
>>> Jan 1 00:00:45 Elphel353 kernel: Empty flash at 0x00b2f0b8 ends at
>>> 0x00b2f800
>>> Jan 1 00:00:45 Elphel353 kernel: Empty flash at 0x00b385e0 ends at
>>> 0x00b38800
>>> Jan 1 00:00:45 Elphel353 kernel: Empty flash at 0x00b45864 ends at
>>> 0x00b46000
>>> Jan 1 00:00:45 Elphel353 kernel: JFFS2 notice: (599) read_dnode: node
>>> CRC failed on dnode at 0xb37fe0: read 0xffffffff, calculated 0x9d8e2f6f
>>> Jan 1 00:00:45 Elphel353 kernel: JFFS2 notice: (599) read_dnode: node
>>> CRC failed on dnode at 0xb457e8: read 0xffffffff, calculated 0x53d88c0d
>>> Jan 1 00:00:45 Elphel353 kernel: JFFS2 notice: (599) check_node_data:
>>> wrong data CRC in data node at 0x00b57800: read 0xb24af98f, calculated
>>> 0xeada2b3.
>>> Jan 1 00:00:45 Elphel353 kernel: eth0: changed MAC to 00:0E:64:08:10:A6
>>> Jan 1 00:00:45 Elphel353 kernel: eth0: changed MAC to 00:0E:64:08:10:A6
>>> Jan 1 00:00:46 Elphel353 udhcpc[719]: udhcpc (v0.9.9-pre) started
>>> Jan 1 00:00:46 Elphel353 ipsetd[728]: Timeout in 120 s.
>>> Jan 1 00:00:46 Elphel353 ipsetd[728]: Expecting echo request payload 408
>>> bytes.
>>> Jan 1 00:00:46 Elphel353 ipsetd[728]: On echo request arrival, execute
>>> /etc/ipsetd.script.
>>> Jan 1 00:00:46 Elphel353 vftpd[734]: Starting vftpd 0.01
>>> Jan 1 00:00:46 Elphel353 vftpd[735]: qos_setup_socket: unsupported AF
>>> Jan 1 00:00:46 Elphel353 udhcpc[719]: Lease of 192.168.2.199 obtained,
>>> lease time 7200
>>> Jan 1 00:00:46 Elphel353 root: DHCP: eth0: IP address: "192.168.2.199"
>>> Jan 1 00:00:46 Elphel353 root: DHCP: eth0: Netmask: "255.255.255.0"
>>> Jan 1 00:00:46 Elphel353 root: DHCP: eth0: Broadcast (server): "",
>>> (deducted): "192.168.2.255"
>>> Jan 1 00:00:47 Elphel353 root: DHCP: eth0: Default gateway: 192.168.2.1
>>> Jan 1 00:00:47 Elphel353 root: DHCP: Domain: 'netbulae.com'
>>> Jan 1 00:00:47 Elphel353 root: DHCP: DNS server(s): '192.168.2.1'
>>> Jan 1 00:00:58 Elphel353 kernel:
>>> arch/cris/arch-v32/drivers/elphel/framepars.c:384:initGlobalPars
>>> GLOBALPARS(G_DEBUG)=0
>>> Jan 1 00:00:58 Elphel353 kernel: initSequencers:resetting both sequencers
>>> Jan 1 00:00:58 Elphel353 kernel:
>>> arch/cris/arch-v32/drivers/elphel/framepars.c:414:initMultiPars
>>> GLOBALPARS(G_MULTI_NUM)=0
>>> Jan 1 00:00:59 Elphel353 kernel: Initializing DMA registers for EXTDMA3
>>> - sensor clock set to 20000000
>>> Jan 1 00:00:59 Elphel353 kernel: 10359 bitstream version =0x0359a04f
>>> Jan 1 00:00:59 Elphel353 kernel: 10353 sensor clock set to 96000000
>>> Jan 1 00:00:59 Elphel353 kernel: 10359A sensor clock set to 96000000
>>> Jan 1 00:00:59 Elphel353 kernel: removing MRST from the sensor
>>> Jan 1 00:00:59 Elphel353 kernel: Setting internal HACT generation
>>> Jan 1 00:00:59 Elphel353 kernel:
>>> arch/cris/arch-v32/drivers/elphel/framepars.c:414:initMultiPars
>>> GLOBALPARS(G_MULTI_NUM)=0
>>> Jan 1 00:00:59 Elphel353 kernel: removing MRST from the sensor
>>> Jan 1 00:00:59 Elphel353 kernel: Found MT9P001 2592x1944 sensor, chip
>>> ID=1801
>>> Jan 1 00:00:59 Elphel353 kernel: trying MT9P001
>>> Jan 1 00:00:59 Elphel353 kernel: Error programming clock 0
>>> fact=96000000, err=0xffffff00
>>> Jan 1 00:00:59 Elphel353 kernel:
>>>
>>> arch/cris/arch-v32/drivers/elphel/multisensor.c:1271:multisensor_pgm_sensorphase
>>> **** ERROR adjusting SDRAM clock phase in
>>>
>>> arch/cris/arch-v32/drivers/elphel/multisensor.c:1272:multisensor_pgm_sensorphase,
>>> result=0xfffffffc
>>> Jan 1 00:00:59 Elphel353 kernel: Resetting MT9X001 sensor^M
>>> Jan 1 00:00:59 Elphel353 kernel: Reading sensor registers to the
>>> shadows:^M
>>> Jan 1 00:00:59 Elphel353 kernel: Initializing MT9X001 registers with
>>> default values:^M
>>> Jan 1 00:00:59 Elphel353 kernel: Starting hardware sequencers
>>> Jan 1 00:02:46 Elphel353 ipsetd[728]: Timed out after 120s.
>>>
>>>
>>> When I try:
>>>
>>> http://elphel.netbulae.com/test/test_inner_10359.php
>>>
>>> I get this result:
>>>
>>> <test name="test_10359">
>>> <board_id result="ok">10359</board_id>
>>> -
>>> <firmware result="fail">
>>> An old firmware revision or i2c doesn't work, got -1
>>> </firmware>
>>> <finish result="fail"/>
>>> </test>
>>>
>>> and "http://elphel.netbulae.com/359/sensors_init.php" gives problem
>>> loading page
>>>
>>> Any idea what might be wrong?
>>>
>>> --
>>> Regards,
>>>
>>> Jorick Astrego
>>> Technisch Directeur
>>>
>>> Netbulae B.V.
>>> Janninksweg 127
>>> 7513 DH Enschede
>>>
>>> Tel. +31 (0)53 - 20 30 270
>>> Fax. +31 (0)53 - 20 30 271
>>>
>>> Email: jorick at netbulae.com
>>> Site: http://www.netbulae.com
>>>
>>>
>>>
>>>
>>> _______________________________________________
>>> Support-list mailing list
>>> Support-list at support.elphel.com
>>>
>>> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
>>>
>>
>>
>>
>> --
>> Met vriendelijke groet,
>>
>> Jorick Astrego
>> Technisch Directeur
>>
>> Netbulae B.V.
>> Janninksweg 127
>> 7513 DH Enschede
>>
>> Tel. +31 (0)53 - 20 30 270
>> Fax. +31 (0)53 - 20 30 271
>>
>> Email: jorick at netbulae.com
>>
>> Site: http://www.netbulae.com
>>
>>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://support.elphel.com/pipermail/support-list_support.elphel.com/attachments/20100806/f7304d25/attachment-0002.html>