[Elphel-support] problem with stereo setup

[Oleg K Dzhimiev]

Dear Jorick,

1. Check the sensors - unscrew the middle cover - attach each cable directly
to the camera. To see if the at least work.

2. Probably just reattaching the cables (one of the sensors should be
connected to J2 (it's the nearest to the 10353-10359 port J1)) to 10359 will
help if the sensors are detected then you'll get lines in the log like:

> Found MT9P001 2592x1944 sensor on 10359A port 1, chip ID=1801
> Found MT9P001 2592x1944 sensor on 10359A port 2, chip ID=1801
>

What is strange is that at least one of the sensors was detected in your
first log but the behavior was as if the TRIG=4.

Best regards,
Oleg

On 6 August 2010 04:14, Jorick Astrego <jorick at netbulae.com> wrote:

>  Dear Oleg/Andrey,
>
> We reverted back to the older firmware 8.0.8.25 as Andrey suggested. One of
> our developers thought the latest CVS version would be better.
>
> After reflashing I tried:
>
> delete /etc/autocampars.xml, disconnect 10359 and rebooting
>
> But still no sensors detected.
>
> When I check "ftp://192.168.2.199/etc/autocampars.xml" the TRIG parameter
> is set to 0, I've attached it to this email
>
> And when I check the sensors, I get:
>
> [root at Elphel353 /root]825# fpcf -i2cr16 4c00
> read failed, returned -1, expected - 2
> [root at Elphel353 /root]825# fpcf -i2cr16 4a00
> read failed, returned -1, expected - 2
> [root at Elphel353 /root]825# fpcf -i2cr16 4e00
> read failed, returned -1, expected - 2
>
> After that I tried:
>
> [root at Elphel353 /root]825# fpcf -X 1
> Clock 1 is OFF
> [root at Elphel353 /root]825# fpcf -X 1 96
> Set clock 1 to 9.600000e+01MHz
> [root at Elphel353 /root]825# fpcf -X 1
> Clock 1 is set to 9.600000e+01MHz
>
> This is is "/var/log/messages
>
> Jan  1 00:00:43 Elphel353 kernel: initSequencers:resetting both sequencers
> Jan  1 00:00:43 Elphel353 kernel: Initializing DMA registers for EXTDMA3 -
> sensor clock set to 20000000
> Jan  1 00:00:43 Elphel353 kernel: 10359 bitstream version =0x0359a04c
> Jan  1 00:00:43 Elphel353 kernel: 10353 sensor clock set to 96000000
> Jan  1 00:00:43 Elphel353 kernel: 10359A sensor clock set to 96000000
> Jan  1 00:00:43 Elphel353 kernel: removing MRST from the sensor
> Jan  1 00:00:43 Elphel353 kernel: removing MRST from the sensor
> Jan  1 00:00:43 Elphel353 kernel: trying MT9P001
> Jan  1 00:00:43 Elphel353 kernel: trying other MT9X001
> Jan  1 00:00:43 Elphel353 kernel: sensor power set low^M
> Jan  1 00:00:43 Elphel353 kernel:  will set to 0x41^M
> Jan  1 00:00:43 Elphel353 kernel: will set to 0x30^M
> Jan  1 00:00:43 Elphel353 kernel: will set to 0x28^M
> Jan  1 00:00:43 Elphel353 kernel: will set to 0x24^M
> Jan  1 00:00:43 Elphel353 kernel: will set to 0x22^M
> Jan  1 00:00:43 Elphel353 kernel: .. full^M
> Jan  1 00:00:43 Elphel353 kernel: Inverted MRST
> Jan  1 00:00:43 Elphel353 kernel: trying MT9X001
> Jan  1 00:00:43 Elphel353 kernel: No image sensor found^M
> Jan  1 00:00:43 Elphel353 kernel:
> arch/cris/arch-v32/drivers/elphel/multisensor.c:1188:multisensor_pgm_sensorphase
> WARNING: ((thispars->pars[P_CLK_SENSOR] == prevpars->pars[P_CLK_SENSOR]))
> but multi_phases_initialized is not yet set ********
> Jan  1 00:00:43 Elphel353 kernel: Error programming clock 0 fact=0,
> err=0xffffff00
> Jan  1 00:00:43 Elphel353 kernel:
> arch/cris/arch-v32/drivers/elphel/multisensor.c:1226:multisensor_pgm_sensorphase
> **** ERROR adjusting SDRAM clock phase in
> arch/cris/arch-v32/drivers/elphel/multisensor.c:1227:multisensor_pgm_sensorphase,
> result=0xfffffffc
> Jan  1 00:02:30 Elphel353 ipsetd[725]: Timed out after 120s.
>
> And on "http://192.168.2.199/359/10359_controls.html"<http://192.168.2.199/359/10359_controls.html>when I press "read registers" I only get "ffffff" in every field.
>
> So there must be something else wrong :-(
>
> Regards,
>
> Jorick
>
>
> On 08/05/2010 07:15 PM, Oleg K Dzhimiev wrote:
>
> Dear Jorick,
>
> You probably got my yesterday's letter in spam... If not - have you tried
> this?
>
>   You're probably using almost the latest software. So, the problem is -
>> the software when detects the 10359 puts the sensors into the triggered mode
>> - and it needs a sync connection with another camera (we use this in our
>> panorama camera).
>>
>> 1.
>> The solution is to get "ftp://192.168.2.199/etc/autocampars.xml" and set
>> the TRIG parameter to 0:
>> old: 4 //external trigger mode
>> new: 0 //free run
>>
>> Copy it back and in a telnet or ssh session launch:
>> "/usr/html/autocampars.php --init" or just reboot
>>
>> 2.
>> To check if the sensors were detected in telnet/ssh/phpshell type:
>> for J2: fpcf -i2cr16 4a00 (result is 0x1801)
>> for J3: fpcf -i2cr16 4c00 (result is 0x1801)
>> for J4: fpcf -i2cr16 4e00 (result is 0x1801) (there is no sensor there but
>> anyway)
>>
>>  About "test_inner_10359.php" -
>
>  <test name="test_10359">
>>
>  <board_id result="ok">10359</board_id>
>>
>  -
>>
>  <firmware result="fail">
>>
>  An old firmware revision or i2c doesn't work, got -1
>>
>  </firmware>
>>
>  <finish result="fail"/>
>>
>  </test>
>>
>
> This can be tested in a telnet/ssh session also:
> a. "fpcf -X 1" - (shoud be 96MHz) frequency to the 10359. "fpcf -X 1 96"
> will turn it on if it's off
> b. If the frequency is on you can read the 10359 registers through
> http://192.168.2.199/359/10359_controls.html
>
> Please modify autocampars.xml first (you can copy the attached one to the
> camera) and then we will move on.
>
> Best regards,
> Oleg
>
> On 5 August 2010 09:18, Jorick Astrego <jorick at netbulae.com> wrote:
>
>>  Dear people,
>>
>> This week we received an elphel assembled stereo setup (two sensors and
>> a 10359 plus crossbar) to hook to our elphel 10353 with 10369.
>>
>> We are running release 8.0.8.37 from cvs
>>
>> The problem is now that we don't receive any image.
>>
>> The 10359 looks ok but doesn't read the registers with the button on:
>>
>> http://elphel.netbulae.com/index.php?site=camerasetup/setup.php
>>
>> I get an error "failed to start"
>>
>> In the /var/log/messages I get this info:
>>
>> Jan 1 00:00:44 Elphel353 syslogd 1.4.1: restart.
>> Jan 1 00:00:44 Elphel353 kernel: klogd 1.4.1, log source = /proc/kmsg
>> started.
>> Jan 1 00:00:44 Elphel353 kernel: Linux version 2.6.19
>> (root at tsarcasm-mobile) (gcc version 3.2.1 Axis release R64/1.64) #1 Wed
>> Aug 4 15:38:13 CEST 2010
>> Jan 1 00:00:44 Elphel353 kernel: Setting up paging and the MMU.
>> Jan 1 00:00:44 Elphel353 kernel: Linux/CRISv32 port on ETRAX FS (C)
>> 2003, 2004 Axis Communications AB
>> Jan 1 00:00:44 Elphel353 kernel: Built 1 zonelists. Total pages: 8160
>> Jan 1 00:00:44 Elphel353 kernel: Kernel command line:
>> root=/dev/mtdblock3 init=/linuxrc rootfstype=jffs2
>> Jan 1 00:00:44 Elphel353 kernel: PID hash table entries: 256 (order: 8,
>> 1024 bytes)
>> Jan 1 00:00:44 Elphel353 kernel: Dentry cache hash table entries: 8192
>> (order: 2, 32768 bytes)
>> Jan 1 00:00:44 Elphel353 kernel: Inode-cache hash table entries: 4096
>> (order: 1, 16384 bytes)
>> Jan 1 00:00:44 Elphel353 kernel: Memory: 41376k/65536k available (1738k
>> kernel code, 24160k reserved, 607k data, 72k init)
>> Jan 1 00:00:44 Elphel353 kernel: Mount-cache hash table entries: 1024
>> Jan 1 00:00:44 Elphel353 kernel: NET: Registered protocol family 16
>> Jan 1 00:00:44 Elphel353 kernel: SCSI subsystem initialized
>> Jan 1 00:00:44 Elphel353 kernel: usbcore: registered new interface
>> driver usbfs
>> Jan 1 00:00:44 Elphel353 kernel: usbcore: registered new interface
>> driver hub
>> Jan 1 00:00:44 Elphel353 kernel: usbcore: registered new device driver usb
>> Jan 1 00:00:44 Elphel353 kernel: NET: Registered protocol family 2
>> Jan 1 00:00:44 Elphel353 kernel: IP route cache hash table entries: 512
>> (order: -2, 2048 bytes)
>> Jan 1 00:00:44 Elphel353 kernel: TCP established hash table entries:
>> 2048 (order: 0, 8192 bytes)
>> Jan 1 00:00:44 Elphel353 kernel: TCP bind hash table entries: 1024
>> (order: -1, 4096 bytes)
>> Jan 1 00:00:44 Elphel353 kernel: TCP: Hash tables configured
>> (established 2048 bind 1024)
>> Jan 1 00:00:44 Elphel353 kernel: TCP reno registered
>> Jan 1 00:00:44 Elphel353 kernel: Check hardware configuration of Elphel
>> 353 camera
>> Jan 1 00:00:44 Elphel353 kernel: Elphel 10349/10369 IO extension board
>> is present
>> Jan 1 00:00:44 Elphel353 kernel: fast_timer_init()
>> Jan 1 00:00:44 Elphel353 kernel: JFFS2 version 2.2. (NAND) (C) 2001-2006
>> Red Hat, Inc.
>> Jan 1 00:00:44 Elphel353 kernel: io scheduler noop registered (default)
>> Jan 1 00:00:44 Elphel353 kernel: Serial: CRISv32 driver $Revision: 1.78
>> $ <6>ttyS0 at I/O 0xb0026000 (irq = 68) is a CRISv32
>> Jan 1 00:00:44 Elphel353 kernel: RAMDISK driver initialized: 16 RAM
>> disks of 4096K size 1024 blocksize
>> Jan 1 00:00:44 Elphel353 kernel: PPP generic driver version 2.4.2
>> Jan 1 00:00:44 Elphel353 kernel: ETRAX FS 10/100MBit ethernet v0.01 (c)
>> 2003 Axis Communications AB
>> Jan 1 00:00:44 Elphel353 kernel: eth0: changed MAC to 00:40:8C:CD:00:00
>> Jan 1 00:00:44 Elphel353 kernel: Uniform Multi-Platform E-IDE driver
>> Revision: 7.00alpha2
>> Jan 1 00:00:44 Elphel353 kernel: ide: Assuming 50MHz system bus speed
>> for PIO modes; override with idebus=xx
>> Jan 1 00:00:44 Elphel353 kernel: ide: ETRAX FS built-in ATA DMA controller
>> Jan 1 00:00:44 Elphel353 kernel: cris_ide_init()
>> Jan 1 00:00:44 Elphel353 kernel: hdb: probing with STATUS(0xca) instead
>> of ALTSTATUS(0x8a)
>> Jan 1 00:00:44 Elphel353 kernel: hdb: no response (status = 0xff),
>> resetting drive
>> Jan 1 00:00:44 Elphel353 kernel: hdb: no response (status = 0xff)
>> Jan 1 00:00:44 Elphel353 kernel: Initializing USB Mass Storage driver...
>> Jan 1 00:00:44 Elphel353 kernel: usbcore: registered new interface
>> driver usb-storage
>> Jan 1 00:00:44 Elphel353 kernel: USB Mass Storage support registered.
>> Jan 1 00:00:44 Elphel353 kernel: usbcore: registered new interface
>> driver usbserial
>> Jan 1 00:00:44 Elphel353 kernel: drivers/usb/serial/usb-serial.c: USB
>> Serial support registered for generic
>> Jan 1 00:00:44 Elphel353 kernel: usbcore: registered new interface
>> driver usbserial_generic
>> Jan 1 00:00:44 Elphel353 kernel: drivers/usb/serial/usb-serial.c: USB
>> Serial Driver core
>> Jan 1 00:00:44 Elphel353 kernel: drivers/usb/serial/usb-serial.c: USB
>> Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter
>> Jan 1 00:00:44 Elphel353 kernel: usbcore: registered new interface
>> driver belkin
>> Jan 1 00:00:45 Elphel353 kernel: drivers/usb/serial/belkin_sa.c: USB
>> Belkin Serial converter driver v1.2
>> Jan 1 00:00:45 Elphel353 kernel: drivers/usb/serial/usb-serial.c: USB
>> Serial support registered for cp2101
>> Jan 1 00:00:45 Elphel353 kernel: usbcore: registered new interface
>> driver cp2101
>> Jan 1 00:00:45 Elphel353 kernel: drivers/usb/serial/cp2101.c: Silicon
>> Labs CP2101/CP2102 RS232 serial adaptor driver v0.07
>> Jan 1 00:00:45 Elphel353 kernel: drivers/usb/serial/usb-serial.c: USB
>> Serial support registered for Garmin GPS usb/tty
>> Jan 1 00:00:45 Elphel353 kernel: usbcore: registered new interface
>> driver garmin_gps
>> Jan 1 00:00:45 Elphel353 kernel: drivers/usb/serial/garmin_gps.c: garmin
>> gps driver v0.28
>> Jan 1 00:00:45 Elphel353 kernel: drivers/usb/serial/usb-serial.c: USB
>> Serial support registered for MCT U232
>> Jan 1 00:00:45 Elphel353 kernel: usbcore: registered new interface
>> driver mct_u232
>> Jan 1 00:00:45 Elphel353 kernel: drivers/usb/serial/mct_u232.c: Magic
>> Control Technology USB-RS232 converter driver z2.0
>> Jan 1 00:00:45 Elphel353 kernel: drivers/usb/serial/usb-serial.c: USB
>> Serial support registered for pl2303
>> Jan 1 00:00:45 Elphel353 kernel: usbcore: registered new interface
>> driver pl2303
>> Jan 1 00:00:45 Elphel353 kernel: drivers/usb/serial/pl2303.c: Prolific
>> PL2303 USB to serial adaptor driver
>> Jan 1 00:00:45 Elphel353 kernel: ETRAX FS stream co-processor driver
>> v0.01, (c) 2003 Axis Communications AB
>> Jan 1 00:00:45 Elphel353 kernel: stream co-processor: init done.
>> Jan 1 00:00:45 Elphel353 kernel: axisflashmap: ...
>> Jan 1 00:00:45 Elphel353 kernel: NAND device: Manufacturer ID: 0x20,
>> Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit)
>> Jan 1 00:00:45 Elphel353 kernel: Additional Info: ID byte3=0x80,
>> byte4=0x1d
>> Jan 1 00:00:45 Elphel353 kernel: Flash is rated 30 ns, modifying
>> bif_core_rw_grp3: old=0x6300483, new=0x6300001
>> Jan 1 00:00:45 Elphel353 kernel: NAND 128MiB 3,3V 8-bit: 0x08000000
>> bytes of NAND flash memory.
>> Jan 1 00:00:45 Elphel353 kernel: axisflashmap: Set to boot from NAND
>> flash, making NAND flash primary device.
>> Jan 1 00:00:45 Elphel353 kernel: axisflashmap: flash read 512 bytes at
>> 0x00040000, data: 00 b0 05 f0 25 ff ed 9c
>> Jan 1 00:00:45 Elphel353 kernel: axisflashmap: partition table offset
>> 10, data: ef be 84 00 a1 0d 00 00
>> Jan 1 00:00:45 Elphel353 kernel: axisflashmap: Found a valid partition
>> table at 0xc02fd9ae-0xc02fda3a.
>> Jan 1 00:00:45 Elphel353 kernel: offset == 0x00040000, size == 0x007C0000
>> Jan 1 00:00:45 Elphel353 kernel: offset == 0x00800000, size == 0x01800000
>> Jan 1 00:00:45 Elphel353 kernel: offset == 0x02000000, size == 0x05000000
>> Jan 1 00:00:45 Elphel353 kernel: offset == 0x07000000, size == 0x00C00000
>> Jan 1 00:00:45 Elphel353 kernel: Creating 1 MTD partitions on "NAND
>> 128MiB 3,3V 8-bit":
>> Jan 1 00:00:45 Elphel353 kernel: 0x00000000-0x08000000 : "main"
>> Jan 1 00:00:45 Elphel353 kernel: Creating 1 MTD partitions on "NAND
>> 128MiB 3,3V 8-bit":
>> Jan 1 00:00:45 Elphel353 kernel: 0x00000000-0x00040000 : "part0"
>> Jan 1 00:00:45 Elphel353 kernel: Creating 1 MTD partitions on "NAND
>> 128MiB 3,3V 8-bit":
>> Jan 1 00:00:45 Elphel353 kernel: 0x00040000-0x00800000 : "part1"
>> Jan 1 00:00:45 Elphel353 kernel: Creating 1 MTD partitions on "NAND
>> 128MiB 3,3V 8-bit":
>> Jan 1 00:00:45 Elphel353 kernel: 0x00800000-0x02000000 : "part2"
>> Jan 1 00:00:45 Elphel353 kernel: Creating 1 MTD partitions on "NAND
>> 128MiB 3,3V 8-bit":
>> Jan 1 00:00:45 Elphel353 kernel: 0x02000000-0x07000000 : "part3"
>> Jan 1 00:00:45 Elphel353 kernel: Creating 1 MTD partitions on "NAND
>> 128MiB 3,3V 8-bit":
>> Jan 1 00:00:45 Elphel353 kernel: 0x07000000-0x07c00000 : "part4"
>> Jan 1 00:00:45 Elphel353 kernel: ETRAX FS GPIO driver v2.5, (c)
>> 2003-2006 Axis Communications AB
>> Jan 1 00:00:45 Elphel353 kernel: Elphel (R) model 353 FPGA (Xilinx (R)
>> XC3S1200E) configuration driver - 132
>> Jan 1 00:00:45 Elphel353 kernel: Elphel (R) model 353 system clocks (PLL
>> frequency synth.) driver - 133
>> Jan 1 00:00:45 Elphel353 kernel: fpga_control- 129
>> Jan 1 00:00:45 Elphel353 kernel:
>> arch/cris/arch-v32/drivers/elphel/framepars.c:384:initGlobalPars
>> GLOBALPARS(G_DEBUG)=0
>> Jan 1 00:00:45 Elphel353 kernel:
>> arch/cris/arch-v32/drivers/elphel/framepars.c:414:initMultiPars
>> GLOBALPARS(G_MULTI_NUM)=0
>> Jan 1 00:00:45 Elphel353 kernel: Elphel (R) Model 353 Frame Parameters
>> device driver - 130
>> Jan 1 00:00:45 Elphel353 kernel: Elphel FPGA interrupts initialized
>> Jan 1 00:00:45 Elphel353 kernel: Initializing DMA registers for EXTDMA3
>> - Elphel (R) Model 353 Camera Driver - 126
>> Jan 1 00:00:45 Elphel353 kernel: Elphel (R) model 353 i2c character
>> device driver - 134, 2 channels
>> Jan 1 00:00:45 Elphel353 kernel: Raw image access driver- 131
>> Jan 1 00:00:45 Elphel353 kernel: Elphel (R) Model 353 video buffer
>> device driver- 135
>> Jan 1 00:00:45 Elphel353 kernel: Elphel (R) model 353 Exif device driver
>> - 125
>> Jan 1 00:00:45 Elphel353 kernel: Starting Elphel (R) Model 353 Gamma
>> Tables device driver - 137
>> Jan 1 00:00:45 Elphel353 kernel: Elphel (R) Model 353 Gamma Tables
>> device driver - 137
>> Jan 1 00:00:45 Elphel353 kernel: Elphel (R) Model 353 Histograms device
>> driver^M
>> Jan 1 00:00:45 Elphel353 kernel: TCP cubic registered
>> Jan 1 00:00:45 Elphel353 kernel: NET: Registered protocol family 1
>> Jan 1 00:00:45 Elphel353 kernel: NET: Registered protocol family 17
>> Jan 1 00:00:45 Elphel353 kernel: VFS: Mounted root (jffs2 filesystem)
>> readonly.
>> Jan 1 00:00:45 Elphel353 kernel: Freeing unused kernel memory: 72k freed
>> Jan 1 00:00:45 Elphel353 kernel: Empty flash at 0x00b20a58 ends at
>> 0x00b21000
>> Jan 1 00:00:45 Elphel353 kernel: Empty flash at 0x00b2f0b8 ends at
>> 0x00b2f800
>> Jan 1 00:00:45 Elphel353 kernel: Empty flash at 0x00b385e0 ends at
>> 0x00b38800
>> Jan 1 00:00:45 Elphel353 kernel: Empty flash at 0x00b45864 ends at
>> 0x00b46000
>> Jan 1 00:00:45 Elphel353 kernel: JFFS2 notice: (599) read_dnode: node
>> CRC failed on dnode at 0xb37fe0: read 0xffffffff, calculated 0x9d8e2f6f
>> Jan 1 00:00:45 Elphel353 kernel: JFFS2 notice: (599) read_dnode: node
>> CRC failed on dnode at 0xb457e8: read 0xffffffff, calculated 0x53d88c0d
>> Jan 1 00:00:45 Elphel353 kernel: JFFS2 notice: (599) check_node_data:
>> wrong data CRC in data node at 0x00b57800: read 0xb24af98f, calculated
>> 0xeada2b3.
>> Jan 1 00:00:45 Elphel353 kernel: eth0: changed MAC to 00:0E:64:08:10:A6
>> Jan 1 00:00:45 Elphel353 kernel: eth0: changed MAC to 00:0E:64:08:10:A6
>> Jan 1 00:00:46 Elphel353 udhcpc[719]: udhcpc (v0.9.9-pre) started
>> Jan 1 00:00:46 Elphel353 ipsetd[728]: Timeout in 120 s.
>> Jan 1 00:00:46 Elphel353 ipsetd[728]: Expecting echo request payload 408
>> bytes.
>> Jan 1 00:00:46 Elphel353 ipsetd[728]: On echo request arrival, execute
>> /etc/ipsetd.script.
>> Jan 1 00:00:46 Elphel353 vftpd[734]: Starting vftpd 0.01
>> Jan 1 00:00:46 Elphel353 vftpd[735]: qos_setup_socket: unsupported AF
>> Jan 1 00:00:46 Elphel353 udhcpc[719]: Lease of 192.168.2.199 obtained,
>> lease time 7200
>> Jan 1 00:00:46 Elphel353 root: DHCP: eth0: IP address: "192.168.2.199"
>> Jan 1 00:00:46 Elphel353 root: DHCP: eth0: Netmask: "255.255.255.0"
>> Jan 1 00:00:46 Elphel353 root: DHCP: eth0: Broadcast (server): "",
>> (deducted): "192.168.2.255"
>> Jan 1 00:00:47 Elphel353 root: DHCP: eth0: Default gateway: 192.168.2.1
>> Jan 1 00:00:47 Elphel353 root: DHCP: Domain: 'netbulae.com'
>> Jan 1 00:00:47 Elphel353 root: DHCP: DNS server(s): '192.168.2.1'
>> Jan 1 00:00:58 Elphel353 kernel:
>> arch/cris/arch-v32/drivers/elphel/framepars.c:384:initGlobalPars
>> GLOBALPARS(G_DEBUG)=0
>> Jan 1 00:00:58 Elphel353 kernel: initSequencers:resetting both sequencers
>> Jan 1 00:00:58 Elphel353 kernel:
>> arch/cris/arch-v32/drivers/elphel/framepars.c:414:initMultiPars
>> GLOBALPARS(G_MULTI_NUM)=0
>> Jan 1 00:00:59 Elphel353 kernel: Initializing DMA registers for EXTDMA3
>> - sensor clock set to 20000000
>> Jan 1 00:00:59 Elphel353 kernel: 10359 bitstream version =0x0359a04f
>> Jan 1 00:00:59 Elphel353 kernel: 10353 sensor clock set to 96000000
>> Jan 1 00:00:59 Elphel353 kernel: 10359A sensor clock set to 96000000
>> Jan 1 00:00:59 Elphel353 kernel: removing MRST from the sensor
>> Jan 1 00:00:59 Elphel353 kernel: Setting internal HACT generation
>> Jan 1 00:00:59 Elphel353 kernel:
>> arch/cris/arch-v32/drivers/elphel/framepars.c:414:initMultiPars
>> GLOBALPARS(G_MULTI_NUM)=0
>> Jan 1 00:00:59 Elphel353 kernel: removing MRST from the sensor
>> Jan 1 00:00:59 Elphel353 kernel: Found MT9P001 2592x1944 sensor, chip
>> ID=1801
>> Jan 1 00:00:59 Elphel353 kernel: trying MT9P001
>> Jan 1 00:00:59 Elphel353 kernel: Error programming clock 0
>> fact=96000000, err=0xffffff00
>> Jan 1 00:00:59 Elphel353 kernel:
>>
>> arch/cris/arch-v32/drivers/elphel/multisensor.c:1271:multisensor_pgm_sensorphase
>> **** ERROR adjusting SDRAM clock phase in
>>
>> arch/cris/arch-v32/drivers/elphel/multisensor.c:1272:multisensor_pgm_sensorphase,
>> result=0xfffffffc
>> Jan 1 00:00:59 Elphel353 kernel: Resetting MT9X001 sensor^M
>> Jan 1 00:00:59 Elphel353 kernel: Reading sensor registers to the
>> shadows:^M
>> Jan 1 00:00:59 Elphel353 kernel: Initializing MT9X001 registers with
>> default values:^M
>> Jan 1 00:00:59 Elphel353 kernel: Starting hardware sequencers
>> Jan 1 00:02:46 Elphel353 ipsetd[728]: Timed out after 120s.
>>
>>
>> When I try:
>>
>> http://elphel.netbulae.com/test/test_inner_10359.php
>>
>> I get this result:
>>
>> <test name="test_10359">
>> <board_id result="ok">10359</board_id>
>> -
>> <firmware result="fail">
>> An old firmware revision or i2c doesn't work, got -1
>> </firmware>
>> <finish result="fail"/>
>> </test>
>>
>> and "http://elphel.netbulae.com/359/sensors_init.php" gives problem
>> loading page
>>
>> Any idea what might be wrong?
>>
>> --
>> Regards,
>>
>> Jorick Astrego
>> Technisch Directeur
>>
>> Netbulae B.V.
>> Janninksweg 127
>> 7513 DH Enschede
>>
>> Tel. +31 (0)53 - 20 30 270
>> Fax. +31 (0)53 - 20 30 271
>>
>> Email: jorick at netbulae.com
>> Site: http://www.netbulae.com
>>
>>
>>
>>
>> _______________________________________________
>> Support-list mailing list
>> Support-list at support.elphel.com
>> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
>>
>
>
>
> --
> Met vriendelijke groet,
>
> Jorick Astrego
> Technisch Directeur
>
> Netbulae B.V.
> Janninksweg 127
> 7513 DH Enschede
>
> Tel. +31 (0)53 - 20 30 270
> Fax. +31 (0)53 - 20 30 271
>
> Email: jorick at netbulae.com
>
> Site: http://www.netbulae.com
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://support.elphel.com/pipermail/support-list_support.elphel.com/attachments/20100806/c8adcdee/attachment-0002.html>