[Elphel-support] how to dump code into camera

[Oleg]

Hi,

Is it during synthesis or implementation?

I think the last time it was built it was ISE WebPack 9.1 or 10.1 - and was
ok. 14.7 looks like working as well. I check the Synthesis only.

You can try:
change all ROM32X1 instances:

> ROM32X1 i_z0 ( .A0(rom_a[0]), .A1(rom_a[1]), .A2(rom_a[2]), .A3(rom_a[3]),
> .A4(rom_a[4]), .O(rom_q[0]));
> ...
> defparam i_z0.INIT = 32'hC67319CC;

to:

> ROM32X1 (.INIT(32'hC67319CC)) i_z0 ( .A0(rom_a[0]), .A1(rom_a[1]),
> .A2(rom_a[2]), .A3(rom_a[3]), .A4(rom_a[4]), .O(rom_q[0]));




On 13 August 2014 02:25, gaurav dasondhi <gauravdasondhi2013 at gmail.com>
wrote:

> Hi
>
> QUESTION
>
> IN ISE WEBPACK DURING IMPLMENT DESIGN I GOT SOME ERRORS. DESIGN SUMMARY
> AND ERRORS ARE GIVEN BLOW.
>
>   Target Device:
>
> xc3s1200e-5ft256
>
> Product Version:
>
> ISE 12.1
>
>    - Warnings:
>
>  836 Warnings (1 new)
>
>    - Errors:
>
>  X 6 Errors (2 new)
>
>
> I GOT THESE 6 EROORS PLEASE PROVIDE SOLUTION.
>
>
> 1.ERROR:LIT:241 - Attribute INIT on ROM32X1 instance
>    "i_compressor/i_quantizator/i_zigzag/i_z5" has a hexadecimal value,
>    "11110000111000001100000010000000", which is too large. INIT should
> contain a
>    maximum of 32 bits.
> ERROR:LIT:241 - Attribute INIT on ROM32X1 instance
>    "i_compressor/i_quantizator/i_zigzag/i_z4" has a hexadecimal value,
>    "10001100100110000011000001100000", which is too large. INIT should
> contain a
>    maximum of 32 bits.
> ERROR:LIT:241 - Attribute INIT on ROM32X1 instance
>    "i_compressor/i_quantizator/i_zigzag/i_z3" has a hexadecimal value,
>    "01001010000001000000110000011000", which is too large. INIT should
> contain a
>    maximum of 32 bits.
> ERROR:LIT:241 - Attribute INIT on ROM32X1 instance
>    "i_compressor/i_quantizator/i_zigzag/i_z2" has a hexadecimal value,
>    "01100011010101111010001001100000", which is too large. INIT should
> contain a
>    maximum of 32 bits.
> ERROR:LIT:239 - Attribute INIT on ROM32X1 instance
>    "i_compressor/i_quantizator/i_zigzag/i_z1" has an invalid hexadecimal
> value,
>    "h611A7896".
> ERROR:LIT:241 - Attribute INIT on ROM32X1 instance
>    "i_compressor/i_quantizator/i_zigzag/i_z0" has a hexadecimal value,
>    "11000110011100110001100111001100", which is too large. INIT should
> contain a
>    maximum of 32 bits.
>
>
>
>
>
> On Tue, Aug 12, 2014 at 3:58 PM, gaurav dasondhi <
> gauravdasondhi2013 at gmail.com> wrote:
>
>> Dear oleg
>>                clarify it : bad bitstream can cause losing connection or
>> damaging the hardware. here damaging hardware means ??
>>
>>               so if i used bad bitstream , then is there  any way to keep
>> camera again to its default setting.?
>>
>>
>>
>> On Tue, Aug 12, 2014 at 1:03 AM, Oleg <support-list at support.elphel.com>
>> wrote:
>>
>>> Guarav,
>>>
>>>
>>> 1. i want to perform correlation between two images ,i have a code
>>>> written in verilog but how to dump that code into camera??
>>>>
>>> If you have a single lens camera (NC353, NC353-... - meaning there's no
>>> 10359 board installed that has an extra fpga) :
>>>
>>> The src verilog files for the system board fpga are here:
>>> http://elphel.cvs.sourceforge.net/viewvc/elphel/elphel353-8.0/fpga/x3x3/
>>> In short, you need to add your code to the project, but most likely it
>>> won't fit in the fpga or won't meet the timing the fpga on the system board
>>> is almost full.
>>>
>>> If you manage to create a bitstream - it should be called x353.bit and
>>> copied it to the camera /etc/ - after rebooting the fpga will be configured
>>> with a new bitstream.
>>> If the camera doesn't have the serial output port on the side
>>> (NC353-369) - it will be hard to debug possible problems - bad bitstream
>>> can cause losing connection or damaging the hardware.
>>>
>>> 2. is iverilog 0.9.5-1 will work instead of 0.9.3 and is we need to
>>>> install icraus verilog as we already have  ISE WEBPACK.??
>>>>
>>>  iverilog 0.9.5-1 should work - never tested though. For verilog
>>> verification you can use both ISE Webpack or Icarus Verilog + GTKWave.
>>>
>>>  3. i installed mplayer by command line but as i typed : mplayer rtsp://
>>>> 192.168.0.9:554 -vo x11 -fs -zoom then camera is in working mode but
>>>> we got blurred image??
>>>>
>>> Blurred - compared to http://192.168.0.9:8081/bimg?
>>>
>>>
>>>
>>>> *SO WHAT I DID IS IT OK OR I NEED TO INSTALL SOMETHING ELSE ????*
>>>
>>> For verilog:
>>>   ISE Webpack, Icarus and GTKWave
>>>
>>> For the camera software:
>>>   cross-compiler, get the camera firmware built from cvs
>>> <http://wiki.elphel.com/index.php?title=Elphel_Software_Kit_for_Ubuntu#Build_Elphel_Software> -
>>> then you can modify sources and rebuild it. KDevelop makes it easier to
>>> navigate through the project.
>>>   Building the firmware requires to have the NFS server set up.
>>>
>>> ImageJ plugins are mostly for our calibrated/stereo/multi-sensor
>>> cameras. You can use them as a base to write your own plugin for
>>> correlation, for example.
>>>
>>>
>>>
>>> Best regards,
>>> Oleg Dzhimiev
>>> Electronics Engineer
>>> phone: +1 801 783 5555 x124
>>> Elphel, Inc.
>>>
>>
>>
>
> _______________________________________________
> Support-list mailing list
> Support-list at support.elphel.com
> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
>
>


-- 
Best regards,
Oleg Dzhimiev
Electronics Engineer
phone: +1 801 783 5555 x124
Elphel, Inc.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://support.elphel.com/pipermail/support-list_support.elphel.com/attachments/20140813/a9b9d17b/attachment-0002.html>