[Elphel-support] strreaming problem...
Carlos Padial
palidoestudio2 at gmail.com
Fri May 18 15:17:28 PDT 2012
ok, here is log from camera boot
ETRAX FS NAND boot loader
=========================
Rev 1, Nov 23 2009 12:31:43
Boot config: 0x00040000->0x40440000, len 0x00200000, boot @ 0x40440000
CPU revision: 0x00000020
Bootloader main at 0x38000ce2
Data end: 0x3800573c
Bss: 0x38008000
Heap: 0x38008000
Identifying nand chip...
maf_id: 0x00000020; dev_id: 0x000000f1
mtd->size == 0x08000000
scan_bbt(); mtd->size == 0x08000000
scan_bbt() ...01; mtd->size == 0x08000000
len == 0x00000100; and BBT_LEN_1 == 0x00000400
scan_bbt() ...02; mtd->size == 0x08000000
scan_bbt() ...03; mtd->size == 0x08000000
scan_bbt() ...1; mtd->size == 0x08000000
scan_bbt() ...2; mtd->size == 0x08000000
scan_bbt() search_read_bbts(); mtd->size == 0x08000000
search_read_bbts() search primary table; mtd->size == 0x08000000
search_bbt() ...1; mtd->size == 0x08000000
search_bbt() ...2; maxblocks: 0x00000004; mtd->size == 0x08000000
Block: 0x000003ff
Check, if we found a bbt for each requested chip
Bad block table found at page0x0000ffc0, version 0x00000001
search_read_bbts() search mirror table
search_bbt() ...1; mtd->size == 0x08000000
search_bbt() ...2; maxblocks: 0x00000004; mtd->size == 0x08000000
Block: 0x000003ff
Block: 0x000003fe
Check, if we found a bbt for each requested chip
Bad block table found at page0x0000ff80, version 0x00000001
scan_bbt() ...3
Done.
Chip identified... 3; NAND 128MiB 3,3V 8-bit
type: 0x00000004
flags: 0x000000c5
size: 0x08000000
erasesize: 0x00020000
oobblock: 0x00000800
oobsize: 0x00000040
ecctype: 0x00000002
eccsize: 0x00000100
Oob info:
useecc: 0x00000002
eccbytes: 0x00000018
eccpos: 0x00000028 0x00000029 0x0000002a 0x0000002b 0x0000002c
0x0000002d 0x0000002e 0x0000002f 0x00000030 0x00000031 0x00000032
0x00000033 0x00000034 0x00000035 0x00000036 0x00000037 0x00000038
0x00000039 0x0000003a 0x0000003b 0x0000003c 0x0000003d 0x0000003e
0x0000003f
Bootload in progress...
New block 0x00040000;len: 0x00200000;start: 0x00040000
New block 0x00060000;len: 0x001e0000;start: 0x00060000
New block 0x00080000;len: 0x001c0000;start: 0x00080000
New block 0x000a0000;len: 0x001a0000;start: 0x000a0000
New block 0x000c0000;len: 0x00180000;start: 0x000c0000
New block 0x000e0000;len: 0x00160000;start: 0x000e0000
New block 0x00100000;len: 0x00140000;start: 0x00100000
New block 0x00120000;len: 0x00120000;start: 0x00120000
New block 0x00140000;len: 0x00100000;start: 0x00140000
New block 0x00160000;len: 0x000e0000;start: 0x00160000
New block 0x00180000;len: 0x000c0000;start: 0x00180000
New block 0x001a0000;len: 0x000a0000;start: 0x001a0000
New block 0x001c0000;len: 0x00080000;start: 0x001c0000
New block 0x001e0000;len: 0x00060000;start: 0x001e0000
New block 0x00200000;len: 0x00040000;start: 0x00200000
New block 0x00220000;len: 0x00020000;start: 0x00220000
complete, status 0x00000000, loaded 0x00200000 bytes
Data in DRAM:
0x25f005b0 0x009cedff 0xbeef05b0
Booting...
Uncompressing Linux...
Done. Now booting the kernel.
Linux version 2.6.19 (oleg at eyesisboxus) (gcc version 3.2.1 Axis
release R64/1.64) #2 Sun Jan 15 18:43:42 MST 2012
Setting up paging and the MMU.
Linux/CRISv32 port on ETRAX FS (C) 2003, 2004 Axis Communications AB
Built 1 zonelists. Total pages: 8160
Kernel command line: root=/dev/mtdblock3 init=/linuxrc rootfstype=jffs2
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 2, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 1, 16384 bytes)
Memory: 40304k/65536k available (1744k kernel code, 25232k reserved,
622k data, 72k init)
Mount-cache hash table entries: 1024
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: -2, 2048 bytes)
TCP established hash table entries: 2048 (order: 0, 8192 bytes)
TCP bind hash table entries: 1024 (order: -1, 4096 bytes)
TCP: Hash tables configured (established 2048 bind 1024)
TCP reno registered
Check hardware configuration of Elphel 353 camera
Elphel 10349/10369 IO extension board is present
fast_timer_init()
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered (default)
Serial: CRISv32 driver $Revision: 1.78 $ <6>ttyS0 at I/O 0xb0026000
(irq = 68) is a CRISv32
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
PPP generic driver version 2.4.2
ETRAX FS 10/100MBit ethernet v0.01 (c) 2003 Axis Communications AB
eth0: changed MAC to 00:40:8C:CD:00:00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
ide: ETRAX FS built-in ATA DMA controller
cris_ide_init()
hda: TOSHIBA MK1231GAL, ATA DISK drive
Physical sector 4096 bytes
Updating sector size to match that of a hard drive: 4096
ide0 at 0x10000000-0x10000007,0x2c000000 on irq 65
hda: max request size: 128KiB
hda: 234441648 sectors (120034 MB), CHS=16383/255/63, (U)DMA
Skipping WIN_SPECIFY for large sectors drive, it is useless here and
likely not supported
Skipping WIN_SPECIFY for large sectors drive, it is useless here and
likely not supported
hda: cache flushes supported
hda: hda1
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for
Belkin / Peracom / GoHubs USB Serial Adapter
usbcore: registered new interface driver belkin
drivers/usb/serial/belkin_sa.c: USB Belkin Serial converter driver v1.2
drivers/usb/serial/usb-serial.c: USB Serial support registered for cp2101
usbcore: registered new interface driver cp2101
drivers/usb/serial/cp2101.c: Silicon Labs CP2101/CP2102 RS232 serial
adaptor driver v0.07
drivers/usb/serial/usb-serial.c: USB Serial support registered for
Garmin GPS usb/tty
usbcore: registered new interface driver garmin_gps
drivers/usb/serial/garmin_gps.c: garmin gps driver v0.28
drivers/usb/serial/usb-serial.c: USB Serial support registered for MCT U232
usbcore: registered new interface driver mct_u232
drivers/usb/serial/mct_u232.c: Magic Control Technology USB-RS232
converter driver z2.0
drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver
ETRAX FS stream co-processor driver v0.01, (c) 2003 Axis Communications AB
stream co-processor: init done.
axisflashmap: ...
NAND device: Manufacturer ID: 0x20, Chip ID: 0xf1 (ST Micro NAND
128MiB 3,3V 8-bit)
Additional Info: ID byte3=0x0, byte4=0x1d
Flash is rated 30 ns, modifying bif_core_rw_grp3: old=0x6300483, new=0x6300001
NAND 128MiB 3,3V 8-bit: 0x08000000 bytes of NAND flash memory.
axisflashmap: Set to boot from NAND flash, making NAND flash primary device.
axisflashmap: flash read 512 bytes at 0x00040000, data: 00 b0 05 f0 25 ff ed 9c
axisflashmap: partition table offset 10, data: ef be 84 00 12 0f 00 00
axisflashmap: Found a valid partition table at 0xc03019ae-0xc0301a3a.
offset == 0x00040000, size == 0x007C0000
offset == 0x00800000, size == 0x01800000
offset == 0x02000000, size == 0x05000000
offset == 0x07000000, size == 0x00C00000
Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x00000000-0x08000000 : "main"
Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x00000000-0x00040000 : "part0"
Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x00040000-0x00800000 : "part1"
Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x00800000-0x02000000 : "part2"
Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x02000000-0x07000000 : "part3"
Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x07000000-0x07c00000 : "part4"
ETRAX FS GPIO driver v2.5, (c) 2003-2006 Axis Communications AB
Elphel (R) model 353 FPGA (Xilinx (R) XC3S1200E) configuration driver - 132
Elphel (R) model 353 system clocks (PLL frequency synth.) driver - 133
fpga_control- 129
arch/cris/arch-v32/drivers/elphel/framepars.c:390:initGlobalPars
GLOBALPARS(G_DEBUG)=0
arch/cris/arch-v32/drivers/elphel/framepars.c:420:initMultiPars
GLOBALPARS(G_MULTI_NUM)=0
Elphel (R) Model 353 Frame Parameters device driver - 130
Elphel FPGA interrupts initialized
Initializing DMA registers for EXTDMA3 - Elphel (R) Model 353 Camera
Driver - 126
Elphel (R) model 353 i2c character device driver - 134, 2 channels
Raw image access driver- 131
Elphel (R) Model 353 video buffer device driver- 135
Elphel (R) model 353 Exif device driver - 125
Starting Elphel (R) Model 353 Gamma Tables device driver - 137
Elphel (R) Model 353 Gamma Tables device driver - 137
Elphel (R) Model 353 Histograms device driver
imu_logger- 141
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
VFS: Mounted root (jffs2 filesystem) readonly.
Freeing unused kernel memory: 72k freed
/linuxrc: Mounting /mnt/flash... Empty flash at 0x00b7e238 ends at 0x00b7e800
Empty flash at 0x01b46038 ends at 0x01b46800
Empty flash at 0x01b5e544 ends at 0x01b5e800
done
/linuxrc: Starting init.
init: starting up.
Starting system initialization.
Axis Linux, http://developer.axis.com/
Copyright (C) 2000-2007 Axis Communications AB
Elphel (R) Model 353 Camera release 8.1.2
* Mounting filesystems...
[ ok ]
* Initializing /var...
[ ok ]
* Determining MAC address...
+ using saved MAC address: 00:0E:64:08:19:B0
[ ok ]
* Initializing random number generator...
[ ok ]
* Setting hostname...
+ hostname: "Elphel353"
[ ok ]
* Initializing volatile resolver configuration...
[ ok ]
* Setting FPGA master clock to 160 MHz...
[ ok ]
* Programming FPGA with /etc/x353.bit...
[ ok ]
* Loaded FPGA rev...
[ 353402b ]
* Adjusting DDR SDRAM clock phase...
[ PH 90/24 ]
* Turn on xtall output (12MHz) to FPGA...
[ ok ]
* Some CMOS-based sensor board attached...
[ assuming 10338 ]
* Configure broadcast ping...
[ ok ]
System initialization is done.
/bin/sh: can't access tty; job control turned off
# New runlevel: 3
* Starting respawn daemon...
[ ok ]
* Starting system and kernel logger...
Jan 1 00:00:18 Elphel353 syslogd 1.4.1: restart.
+ system logger started
+ kernel logger started
[ ok ]
* Bringing lo up...
[ ok ]
* Bringing eth0 up...
eth0: changed MAC to 00:0E:64:08:19:B0
+ hardware address: 00:0E:64:08:19:B0
+ media: auto
+ eth0 going up
eth0: changed MAC to 00:0E:64:08:19:B0
+ IPv4 on eth0
+ boot protocol: none
+ IP address: 192.168.0.9
+ netmask: 255.255.255.0
+ broadcast address: 192.168.0.255
+ default IPv4 gateway: 192.168.0.15
+ set MDI to MDI (normal) mode
y
+ done
[ ok ]
* Waiting for a network interface...
+ eth0 is up
[ ok ]
* Starting ipsetd...
Jan 1 00:00:20 Elphel353 ipsetd[709]: Timeout in 120 s.
Jan 1 00:00:20 Elphel353 ipsetd[709]: Expecting echo request payload 408 bytes.
Jan 1 00:00:20 Elphel353 ipsetd[709]: On echo request arrival,
execute /etc/ipsetd.script.
[ ok ]
* Starting telnet server...
telnetd: starting
port: 23; interface: any; login program: /bin/login;
maximum number of allowed simultaneous clients: unlimited
[ ok ]
* Starting ftp server...
Jan 1 00:00:20 Elphel353 vftpd[715]: Starting vftpd 0.01
Jan 1 00:00:20 Elphel353 vftpd[716]: qos_setup_socket: unsupported AF
[ ok ]
* Starting ssh server...
Jan 1 00:00:21 Elphel353 dropbear[727]: Running in background
[ ok ]
* Starting mii-diag...
[ ok ]
* Starting image server on port 8081, making Exif...
[ ok ]
* Flushing JFFS2 (sync)...
[ ok ]
* Starting autocampars daemon...
[ ok ]
* Starting autoexposure daemon...
autoexposure started, daemon_bit=0x0, debug=0x1
autoexposure.c:126:main: autoexposure started, daemon_bit=0x0, debug=0x1
[ ok ]
* Starting ccamftp daemon...
[ ok ]
* initializing camera/sensor parameters...
arch/cris/arch-v32/drivers/elphel/framepars.c:390:initGlobalPars
GLOBALPARS(G_DEBUG)=0
initSequencers:resetting both sequencers
arch/cris/arch-v32/drivers/elphel/framepars.c:420:initMultiPars
GLOBALPARS(G_MULTI_NUM)=0
sensor clock set to 20000000
removing MRST from the sensor
Found MT9P001 2592x1944 sensor, chip ID=1801
trying MT9P001
Resetting MT9X001 sensor
Reading sensor registers to the shadows:
Initializing MT9X001 registers with default values:
Starting hardware sequencers
[ ok ]
* Starting lighttpd web server...
[ ok ]
* Setting time from NTP server...
[ unavailable ]
* Looking for I/O board...
[ 10369"A" ]
ETRAX FS IOP USB Host Controller version 1.10 (c) 2004, 2005,
2006 Axis Communications AB
crisv32_hc crisv32_hc.0: ETRAX FS IOP USB Host Controller
crisv32_hc crisv32_hc.0: new USB bus registered, assigned bus number 1
crisv32_hc crisv32_hc.0: irq 51, io base 0x00000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
crisv32_hc crisv32_hc.0: ETRAX FS IOP USB Host Controller
usbcore: registered new interface driver snd-usb-audio
usbcore: registered new interface driver snd-usb-caiaq
* Initializing USB hub...
[ ok ]
* Setting system time from CMOS clock...
usb 1-1: new full speed USB device using crisv32_hc and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
[ Fri May 18 21:41:48 UTC 2012 ]
* Starting video streamer...
[ ok ]
* Starting IMU/GPS/compass...
[ none ]
launcher: nothing to launch
All scripts for runlevel 3 done in 89.71s.
May 18 21:42:51 Elphel353 ipsetd[709]: Timed out after 120s.
#######################################################################################################################################
and now top just after boot
Mem: 24440K used, 15936K free, 0K shrd, 0K buff, 14808K cached
CPU: 0% usr 0% sys 0% nic 99% idle 0% io 0% irq 0% sirq
Load average: 0.21 0.15 0.09 2/34 860
PID PPID USER STAT VSZ %MEM %CPU COMMAND
860 854 root R 1496 4% 0% top
751 1 root S 4136 10% 0% /usr/local/sbin/autoexposure
827 1 root S 44912 111% 0% /usr/local/bin/str
829 827 root S 44912 111% 0% /usr/local/bin/str
830 829 root S 44912 111% 0% /usr/local/bin/str
763 759 root S 30872 76% 0% /usr/local/sbin/php
764 763 root S 30872 76% 0% /usr/local/sbin/php
765 763 root S 30872 76% 0% /usr/local/sbin/php
759 1 root S 4976 12% 0% /usr/local/sbin/lighttpd -f /etc/light
727 1 root S 1480 4% 0% /usr/sbin/dropbear
716 1 root S 1432 4% 0% /bin/vftpd -r
854 712 root S 1352 3% 0% -sh
647 1 root S 1352 3% 0% /bin/sh
654 1 root S 1312 3% 0% /usr/sbin/syslogd -m 0 -o 40000
657 1 root S 1144 3% 0% /usr/sbin/klogd -x
1 0 root S 1136 3% 0% init
712 1 root S 1136 3% 0% /bin/utelnetd -d
651 1 root S 1136 3% 0% /sbin/respawnd
746 1 root S 1136 3% 0% /usr/local/sbin/imgsrv -p 8081
752 1 root S 1120 3% 0% /usr/local/sbin/launch_php_script 2 /u
####
i setup camera to 1280x720 @ 24.989 fps 51K
run mplayer
MPlayer SVN-r33713-4.6.1 (C) 2000-2011 MPlayer Team
mplayer: could not connect to socket
mplayer: No such file or directory
Failed to open LIRC support. You will not be able to use your remote control.
Playing rtsp://192.168.0.9:554.
Resolving 192.168.0.9 for AF_INET6...
Couldn't resolve name for AF_INET6: 192.168.0.9
Connecting to server 192.168.0.9[192.168.0.9]: 554...
rtsp_session: unsupported RTSP server. Server type is 'unknown'.
Resolving 192.168.0.9 for AF_INET6...
Couldn't resolve name for AF_INET6: 192.168.0.9
Connecting to server 192.168.0.9[192.168.0.9]: 554...
http_read_response read 0 (i.e. EOF).
No stream found to handle url rtsp://192.168.0.9:554
Exiting... (End of file)
i cant get the stream with the same computer,
i setup camera to 640x480 @ 24.989 fps 18K
and launch mplayer from other laptop ubuntu in the same lan
(the camera is conected to a router, and also the pcs)
--------------------------
top while running (non stop)
Mem: 27264K used, 13112K free, 0K shrd, 0K buff, 16248K cached
CPU: 0% usr 3% sys 0% nic 94% idle 0% io 0% irq 1% sirq
Load average: 0.02 0.08 0.08 2/34 1129
PID PPID USER STAT VSZ %MEM %CPU COMMAND
830 829 root S 44928 111% 4% /usr/local/bin/str
860 854 root R 1496 4% 0% top
751 1 root R 4136 10% 0% /usr/local/sbin/autoexposure
827 1 root S 44928 111% 0% /usr/local/bin/str
829 827 root S 44928 111% 0% /usr/local/bin/str
765 763 root S 30936 76% 0% /usr/local/sbin/php
764 763 root S 30936 76% 0% /usr/local/sbin/php
763 759 root S 30872 76% 0% /usr/local/sbin/php
759 1 root S 5288 13% 0% /usr/local/sbin/lighttpd -f /etc/light
727 1 root S 1480 4% 0% /usr/sbin/dropbear
716 1 root S 1432 4% 0% /bin/vftpd -r
854 712 root S 1352 3% 0% -sh
647 1 root S 1352 3% 0% /bin/sh
654 1 root S 1312 3% 0% /usr/sbin/syslogd -m 0 -o 40000
657 1 root S 1144 3% 0% /usr/sbin/klogd -x
1 0 root S 1136 3% 0% init
746 1 root S 1136 3% 0% /usr/local/sbin/imgsrv -p 8081
712 1 root S 1136 3% 0% /bin/utelnetd -d
651 1 root S 1136 3% 0% /sbin/respawnd
752 1 root S 1120 3% 0% /usr/local/sbin/launch_php_script 2 /u
i setup again to 1280x720 @ 24.989 fps 51K
and launch mplayer from the other laptop
top while running mplayer (about 10 seconds)
Mem: 27376K used, 13000K free, 0K shrd, 0K buff, 16248K cached
CPU: 0% usr 4% sys 0% nic 92% idle 0% io 0% irq 1% sirq
Load average: 0.29 0.14 0.10 2/34 1189
PID PPID USER STAT VSZ %MEM %CPU COMMAND
860 854 root R 1496 4% 0% top
854 712 root S 1352 3% 0% -sh
830 829 root S 44928 111% 6% /usr/local/bin/str
and now top before mplayer crashes
Mem: 27296K used, 13080K free, 0K shrd, 0K buff, 16248K cached
CPU: 0% usr 0% sys 0% nic 98% idle 0% io 0% irq 1% sirq
Load average: 0.41 0.19 0.12 2/34 1189
PID PPID USER STAT VSZ %MEM %CPU COMMAND
860 854 root R 1496 4% 0% top
854 712 root S 1352 3% 0% -sh
830 829 root S 44928 111% 0% /usr/local/bin/str
829 827 root S 44928 111% 0% /usr/local/bin/str
827 1 root S 44928 111% 0% /usr/local/bin/str
765 763 root S 30936 76% 0% /usr/local/sbin/php
764 763 root S 30936 76% 0% /usr/local/sbin/php
763 759 root S 30872 76% 0% /usr/local/sbin/php
759 1 root S 5296 13% 0% /usr/local/sbin/lighttpd -f /etc/light
752 1 root S 1120 3% 0% /usr/local/sbin/launch_php_script 2 /u
751 1 root S 4136 10% 0% /usr/local/sbin/autoexposure
750 1 root R 1120 3% 0% /usr/local/sbin/autocampars
746 1 root S 1136 3% 0% /usr/local/sbin/imgsrv -p 8081
727 1 root S 1480 4% 0% /usr/sbin/dropbear
716 1 root S 1432 4% 0% /bin/vftpd -r
712 1 root S 1136 3% 0% /bin/utelnetd -d
657 1 root S 1144 3% 0% /usr/sbin/klogd -x
654 1 root S 1312 3% 0% /usr/sbin/syslogd -m 0 -o 40000
651 1 root S 1136 3% 0% /sbin/respawnd
647 1 root S 1352 3% 0% /bin/sh
then the camera dont respond and hangs, last top showed is:
Mem: 27344K used, 13032K free, 0K shrd, 0K buff, 16248K cached
CPU: 0% usr 4% sys 0% nic 91% idle 0% io 0% irq 2% sirq
Load average: 0.03 0.11 0.09 2/34 1190
PID PPID USER STAT VSZ %MEM %CPU COMMAND
830 829 root S 44928 111% 7% /usr/local/bin/str
1190 854 root R 1496 4% 0% top
827 1 root S 44928 111% 0% /usr/local/bin/str
2012/5/18 Oleg <support-list at support.elphel.com>:
>> 2. Command "top" right after the boot + before/after you launch
>> mplayer could be helpful.
>
> I meant before the mplayer crashes.
>
> On 18 May 2012 12:52, Oleg <support-list at support.elphel.com> wrote:
>>
>> Carlos,
>>
>> "Top"s look ok. I also tried a camera with the 8.1.2 firmware and my PC -
>> streaming works at 1920x1088.
>>
>> Sorry, I forgot to ask you to check a few more things:
>>
>> 1. You should have a usb-serial cable - could you connect it and send us
>> the camera boot log? And also the info the camera writes when the streamer
>> is working.
>> 2. Command "top" right after the boot + before/after you launch
>> mplayer could be helpful.
>>
>> Best regards,
>> Oleg Dzhimiev
>> Electronics Engineer
>> phone: +1 801 783 5555 x124
>> Elphel, Inc.
>>
>>
>> On 18 May 2012 06:53, Carlos Padial <palidoestudio2 at gmail.com> wrote:
>>>
>>> > PC's OS - ?
>>>
>>> ok, lets me explain...
>>>
>>> i have two computers. A netbook (samsung n150, atom) with linux mint
>>> 12 32 bits, ubuntu 10.10 32 bits, and with this computer i also use
>>> the live usb.
>>>
>>> The second one is an intel i7 with linux mint 12 64bits, ubuntu 12.04
>>> 32bits, (and till yesterday ubuntu 11.10)
>>> When i try the live usb with this computer it works badly...
>>> (resolution is 640x400 and window management gests crazy everytime...
>>> making it unusable...
>>>
>>> When i have tried to install the usb, it doenst seems to recognice the
>>> password i entered during the instalation so i'm only working with the
>>> live version.
>>>
>>> I have tried mplayer with all of this OS and the results are similar.
>>>
>>> With the liveusb in the atom netbook i believe the problem is that the
>>> netbook seems not to be able to open high resolution streams, with
>>> 1920x1088 (128K) dont show any image, but i tried 640x480 (24k) and
>>> the image is showed and even mantained for a long time (30-50 seconds)
>>> But after that mplayer exits
>>>
>>> The best results i had was in the i7 with ubuntu 12, mplayer (MPlayer
>>> svn r34540 (Ubuntu) and 640x480 (24k) , the live preview was working
>>> without stop (i stopped it)
>>>
>>> when i setup 1280x720 (73k) and mplayer dont show the image...
>>> i come back to 640x480 (27k) and the live preview works fine... this
>>> is the only setup showing the live preview non stop...
>>>
>>> with 800x600 (40k) the preview show the image for 2 seconds and then
>>> stops..
>>> above this resolution the image is not showed (only one time each 10...
>>>
>>> > Camera firmware - ?
>>>
>>> Firmware Version: Elphel (R) Model 353 Camera release 8.1.2
>>>
>>> > FPS = 24?
>>>
>>> now i'm limitting fps to 25 (using instructions from wiki FPScontrol)
>>>
>>> > Image dimensions and size - 1920x1088, 100-150KB?
>>>
>>> > Mplayer version (let's stick to mplayer)?
>>>
>>> MPlayer svn r34540 (Ubuntu) (in ubuntu 12, where i have the best
>>> results for the moment)
>>>
>>> > During that 5-10 sec of working the window with image opens, right? or
>>> > it
>>>
>>> > just crashes not showing anything?
>>>
>>> when i say mplayer is working i mean it opens a window and the image
>>> is showed. Then the window close and mplayer says:
>>>
>>> Exiting... (End of file)
>>>
>>> > 2. Some things that you could try:
>>> > Does mplayer act the same if you boot from our LiveUSB?
>>>
>>> Yes, the response is similar but i need to run liveUSB correctly in
>>> the i7 to test...
>>>
>>> > Check the CPU usage on the camera - "top" or "ps" from the telnet
>>> > session -
>>> > could also you send us this info?
>>>
>>>
>>> top-------------------------------------------------------------------------------------------
>>>
>>> Mem: 27384K used, 12992K free, 0K shrd, 0K buff, 16248K cached
>>> CPU: 0% usr 0% sys 0% nic 98% idle 0% io 0% irq 0% sirq
>>> Load average: 0.27 0.26 0.26 5/34 2001
>>> PID PPID USER STAT VSZ %MEM %CPU COMMAND
>>> 751 1 root S 4136 10% 1% /usr/local/sbin/autoexposure
>>> 2001 1996 root R 1496 4% 0% top
>>> 830 829 root S 44928 111% 0% /usr/local/bin/str
>>> 827 1 root S 44928 111% 0% /usr/local/bin/str
>>> 829 827 root S 44928 111% 0% /usr/local/bin/str
>>> 765 763 root S 30936 76% 0% /usr/local/sbin/php
>>> 764 763 root S 30936 76% 0% /usr/local/sbin/php
>>> 763 759 root S 30872 76% 0% /usr/local/sbin/php
>>> 759 1 root S 5336 13% 0% /usr/local/sbin/lighttpd -f
>>> /etc/light
>>> 727 1 root S 1480 4% 0% /usr/sbin/dropbear
>>> 716 1 root S 1432 4% 0% /bin/vftpd -r
>>> 1996 712 root S 1352 3% 0% -sh
>>> 647 1 root S 1352 3% 0% /bin/sh
>>> 654 1 root S 1312 3% 0% /usr/sbin/syslogd -m 0 -o 40000
>>> 657 1 root S 1144 3% 0% /usr/sbin/klogd -x
>>> 1 0 root S 1136 3% 0% init
>>> 746 1 root S 1136 3% 0% /usr/local/sbin/imgsrv -p 8081
>>> 651 1 root S 1136 3% 0% /sbin/respawnd
>>> 712 1 root S 1136 3% 0% /bin/utelnetd -d
>>> 752 1 root S 1120 3% 0%
>>> /usr/local/sbin/launch_php_script 2 /u
>>>
>>> this is top with the camera configured with 1280x720 (73k)
>>> then i start mplayer in other terminal and the streamed video is
>>> showed for 2 seconds... when the mplayer stop, top show this other
>>> info:
>>>
>>> Mem: 27456K used, 12920K free, 0K shrd, 0K buff, 16248K cached
>>> CPU: 0% usr 1% sys 0% nic 97% idle 0% io 0% irq 1% sirq
>>> Load average: 0.20 0.24 0.25 2/34 2001
>>> PID PPID USER STAT VSZ %MEM %CPU COMMAND
>>> 2001 1996 root R 1496 4% 1% top
>>> 751 1 root S 4136 10% 0% /usr/local/sbin/autoexposure
>>> 830 829 root S 44928 111% 0% /usr/local/bin/str
>>> 750 1 root R 1120 3% 0% /usr/local/sbin/autocampars
>>> 827 1 root S 44928 111% 0% /usr/local/bin/str
>>> 829 827 root S 44928 111% 0% /usr/local/bin/str
>>> 765 763 root S 30936 76% 0% /usr/local/sbin/php
>>> 764 763 root S 30936 76% 0% /usr/local/sbin/php
>>> 763 759 root S 30872 76% 0% /usr/local/sbin/php
>>> 759 1 root S 5336 13% 0% /usr/local/sbin/lighttpd -f
>>> /etc/light
>>> 727 1 root S 1480 4% 0% /usr/sbin/dropbear
>>> 716 1 root S 1432 4% 0% /bin/vftpd -r
>>> 1996 712 root S 1352 3% 0% -sh
>>> 647 1 root S 1352 3% 0% /bin/sh
>>> 654 1 root S 1312 3% 0% /usr/sbin/syslogd -m 0 -o 40000
>>>
>>> ps-------------------------------------------
>>>
>>> PID USER VSZ STAT COMMAND
>>>
>>> 1 root 1136 S init
>>> 2 root 0 SWN [ksoftirqd/0]
>>> 3 root 0 SW [watchdog/0]
>>> 4 root 0 SW< [events/0]
>>> 5 root 0 SW< [khelper]
>>> 6 root 0 SW< [kthread]
>>> 8 root 0 SW< [kblockd/0]
>>> 11 root 0 SW< [khubd]
>>> 23 root 0 SW [pdflush]
>>> 24 root 0 SW [pdflush]
>>> 25 root 0 SW< [kswapd0]
>>> 26 root 0 SW< [aio/0]
>>> 568 root 0 SW [mtdblockd]
>>> 602 root 0 SWN [jffs2_gcd_mtd4]
>>> 647 root 1352 S /bin/sh
>>> 651 root 1136 S /sbin/respawnd
>>> 654 root 1312 S /usr/sbin/syslogd -m 0 -o 40000
>>> 657 root 1144 S /usr/sbin/klogd -x
>>> 712 root 1136 S /bin/utelnetd -d
>>> 716 root 1432 S /bin/vftpd -r
>>> 727 root 1480 S /usr/sbin/dropbear
>>> 746 root 1136 S /usr/local/sbin/imgsrv -p 8081
>>> 750 root 1120 S /usr/local/sbin/autocampars
>>> 751 root 4136 S /usr/local/sbin/autoexposure
>>> 752 root 1120 S /usr/local/sbin/launch_php_script 2
>>> /usr/local/sbin/c
>>> 759 root 5336 S /usr/local/sbin/lighttpd -f /etc/lighttpd.conf
>>> -m /us
>>> 763 root 30872 S /usr/local/sbin/php
>>> 764 root 30936 S /usr/local/sbin/php
>>> 765 root 30936 S /usr/local/sbin/php
>>> 827 root 44928 S /usr/local/bin/str
>>> 829 root 44928 S /usr/local/bin/str
>>> 830 root 44928 S /usr/local/bin/str
>>> 1996 root 1352 S -sh
>>> 2002 root 1488 R ps
>>>
>>> usually when i use telnet after mplayer exits, telnet didnt respond for a
>>> while.
>>>
>>> it seems that with gstreamer when this happends, i need to restart the
>>> camera, but with mplayer i dont need to restart the camera (yet)
>>>
>>> > Your PC/laptop CPU usage?
>>>
>>> top running in my i7 (ubuntu 12.04) shows:
>>>
>>> top - 13:55:00 up 1:49, 4 users, load average: 0.92, 0.97, 1.04
>>> Tasks: 198 total, 2 running, 196 sleeping, 0 stopped, 0 zombie
>>> Cpu(s): 1.8%us, 0.5%sy, 0.0%ni, 97.7%id, 0.0%wa, 0.0%hi, 0.0%si,
>>> 0.0%st
>>> Mem: 12401224k total, 2853840k used, 9547384k free, 142224k buffers
>>> Swap: 524284k total, 0k used, 524284k free, 1919880k cached
>>>
>>> PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
>>> 2662 root 20 0 70732 51m 12m S 6 0.4 7:02.82 Xorg
>>> 3346 carlos 20 0 467m 161m 23m S 3 1.3 5:35.28
>>> plugin-containe
>>> 2913 carlos 20 0 328m 164m 38m S 2 1.4 13:12.51 compiz
>>> 1659 carlos 9 -11 171m 5696 4104 S 1 0.0 1:23.66
>>> pulseaudio
>>> 3884 carlos 20 0 96084 17m 11m S 1 0.1 0:29.12
>>> gnome-terminal
>>> 3309 carlos 20 0 547m 179m 32m S 0 1.5 4:15.87 firefox
>>> 5669 root 20 0 0 0 0 S 0 0.0 0:00.91
>>> kworker/0:1
>>> 5825 carlos 20 0 2836 1200 884 R 0 0.0 0:00.03 top
>>> 1 root 20 0 3636 1984 1284 S 0 0.0 0:01.26 init
>>> 2 root 20 0 0 0 0 S 0 0.0 0:00.00 kthreadd
>>> 3 root 20 0 0 0 0 S 0 0.0 0:00.12
>>> ksoftirqd/0
>>> 6 root RT 0 0 0 0 S 0 0.0 0:00.00
>>> migration/0
>>> 7 root RT 0 0 0 0 S 0 0.0 2:09.07
>>> watchdog/0
>>> 8 root RT 0 0 0 0 S 0 0.0 0:00.00
>>> migration/1
>>> 10 root 20 0 0 0 0 S 0 0.0 0:00.05
>>> ksoftirqd/1
>>> 12 root RT 0 0 0 0 S 0 0.0 0:29.46
>>> watchdog/1
>>> 13 root RT 0 0 0 0 S 0 0.0 0:00.00
>>> migration/2
>>> 15 root 20 0 0 0 0 S 0 0.0 0:00.05
>>> ksoftirqd/2
>>> 16 root RT 0 0 0 0 S 0 0.0 0:00.01
>>> watchdog/2
>>> 17 root RT 0 0 0 0 S 0 0.0 0:00.00
>>> migration/3
>>> 19 root 20 0 0 0 0 S 0 0.0 0:00.03
>>> ksoftirqd/3
>>> 20 root RT 0 0 0 0 S 0 0.0 0:00.04
>>> watchdog/3
>>> 21 root RT 0 0 0 0 S 0 0.0 0:00.00
>>> migration/4
>>> 23 root 20 0 0 0 0 S 0 0.0 0:00.01
>>> ksoftirqd/4
>>> 24 root RT 0 0 0 0 S 0 0.0 0:00.01
>>> watchdog/4
>>> 25 root RT 0 0 0 0 S 0 0.0 0:00.00
>>> migration/5
>>> 27 root 20 0 0 0 0 S 0 0.0 0:00.00
>>> ksoftirqd/5
>>> 28 root RT 0 0 0 0 S 0 0.0 0:00.01
>>> watchdog/5
>>> 29 root RT 0 0 0 0 S 0 0.0 0:00.00
>>> migration/6
>>> 30 root 20 0 0 0 0 S 0 0.0 0:00.00
>>> kworker/6:0
>>> 31 root 20 0 0 0 0 S 0 0.0 0:00.00
>>> ksoftirqd/6
>>> 32 root RT 0 0 0 0 S 0 0.0 0:00.01
>>> watchdog/6
>>> 33 root RT 0 0 0 0 S 0 0.0 0:00.00
>>> migration/7
>>> 35 root 20 0 0 0 0 S 0 0.0 0:00.01
>>> ksoftirqd/7
>>> 36 root RT 0 0 0 0 S 0 0.0 0:00.01 watchdog/7
>>>
>>> > Best regards,
>>> > Oleg Dzhimiev
>>> > Electronics Engineer
>>> > phone: +1 801 783 5555 x124
>>> > Elphel, Inc.
>>>
>>>
>>>
>>> --
>>> Carlos Padial
>>> surreal.asturnazari.es
>>>
>>> _______________________________________________
>>> Support-list mailing list
>>> Support-list at support.elphel.com
>>>
>>> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
>>
>>
>>
>
>
>
> --
> Best regards,
> Oleg Dzhimiev
> Electronics Engineer
> phone: +1 801 783 5555 x124
> Elphel, Inc.
--
Carlos Padial
surreal.asturnazari.es
More information about the Support-list
mailing list