[Elphel-support] strreaming problem...

[Oleg]

Does mplayer work with all resolutions? Could you try it?

> mplayer rtsp://192.168.0.9:554 -vo x11 -zoom


Also, is the scene static? what is the maximum exposure? Does the fps
indicator go red (meaning the exposure exceeds the frame rate)?

Best regards,
Oleg Dzhimiev
Electronics Engineer
phone: +1 801 783 5555 x124
Elphel, Inc.


On 16 May 2012 06:00, Carlos Padial <palidoestudio2 at gmail.com> wrote:

> when i run this (with resolution 1920x1088):
>
> $ gst-launch rtspsrc location=rtsp://192.168.0.9:554 latency=100 !
> rtpjpegdepay ! jpegdec ! autovideosink
> Estableciendo el conducto a PAUSA …
> El conducto está vivo y no necesita PREPARARSE …
> Estableciendo el conducto a REPRODUCIENDO …
> New clock: GstSystemClock
>
> and gstreamer hangs until i press ctrl+c...
>
> while gstreamer is active, no video is showed and no telnet, neither ssh
> can be done...
>
> when i cancel gstreamer i can restart ssh and telnet,
>
> but camcv dont work until i restart the camera... with this message:
> JavaScript: Aborted as retry counter expired
>
>
> 2012/5/16 Sebastian Pichelhofer <sebastian.pichelhofer at gmail.com>
>
>> Can you still SSH to the camera when this happens?
>> If yes, is the str (streamer) process still running properly or did it
>> crash?
>>
>> Regards Sebastian
>>
>> On Wed, May 16, 2012 at 1:02 PM, Carlos Padial <palidoestudio2 at gmail.com>wrote:
>>
>>> i had a problem with the streaming...
>>>
>>> i start the camera and launch a simple stream viewer with:
>>> gst-launch rtspsrc location=rtsp://192.168.0.9:554 latency=100 !
>>> rtpjpegdepay ! jpegdec ! autovideosink
>>>
>>> and i can see the video working fine.
>>>
>>> Then i go to camcv and set the sensor to 1920x1088 (or 1280x720) (i
>>> tried also limitting the framerate and manual exposure...)
>>>
>>> when i launch again gstreamer, the stream never start, and the network
>>> stops working. The camera remains with green and yellow leds on, and the
>>> Internet conection is collapsed for all computers in the net until i
>>> restart the camera.
>>>
>>> it has been happening a lot of times. Normally gstreamer and vlc are
>>> only able to see the strream when working at full resolution. Sometimes the
>>> gstreamer shows the video with other resolutions, and works fine, but
>>> suddenly it fails and i cant find a reason for this...
>>>
>>> (the camera freezes only when reading the stream. When recording from
>>> camogmgui it works ok at any resolution)
>>>
>>> any ideas?
>>>
>>> --
>>> Carlos Padial
>>> surreal.asturnazari.es
>>>
>>> _______________________________________________
>>> Support-list mailing list
>>> Support-list at support.elphel.com
>>>
>>> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
>>>
>>>
>>
>
>
> --
> Carlos Padial
> surreal.asturnazari.es
>
> _______________________________________________
> Support-list mailing list
> Support-list at support.elphel.com
> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://support.elphel.com/pipermail/support-list_support.elphel.com/attachments/20120516/fc12a842/attachment-0002.html>