[Elphel-support] hdd without partition
Oleg
support-list at support.elphel.com
Mon Mar 19 12:44:46 PDT 2012
Dear Carlos,
Below I pasted the serial port output when the HDD is detected.
Could you please compare the place I marked with what you are getting - are
there any errors?
Please, also check the cable is properly
connected<http://wiki.elphel.com/index.php?title=File:Connect_internal_disk.jpeg>-
foil contacts should be facing the pins of the adapter board.
Best regards,
Oleg Dzhimiev
ETRAX FS NAND boot
loader
=========================
Rev 1, Nov 23 2009
12:31:43
Boot config: 0x00040000->0x40440000, len 0x00200000, boot @
0x40440000
CPU revision:
0x00000020
Bootloader main at
0x38000ce2
Data end:
0x3800573c
Bss:
0x38008000
Heap:
0x38008000
Identifying nand
chip...
maf_id: 0x00000020; dev_id:
0x000000f1
mtd->size ==
0x08000000
scan_bbt(); mtd->size ==
0x08000000
scan_bbt() ...01; mtd->size ==
0x08000000
len == 0x00000100; and BBT_LEN_1 ==
0x00000400
scan_bbt() ...02; mtd->size ==
0x08000000
scan_bbt() ...03; mtd->size ==
0x08000000
scan_bbt() ...1; mtd->size ==
0x08000000
scan_bbt() ...2; mtd->size ==
0x08000000
scan_bbt() search_read_bbts(); mtd->size ==
0x08000000
search_read_bbts() search primary table; mtd->size ==
0x08000000
search_bbt() ...1; mtd->size ==
0x08000000
search_bbt() ...2; maxblocks: 0x00000004; mtd->size ==
0x08000000
Block:
0x000003ff
Check, if we found a bbt for each requested
chip
Bad block table found at page0x0000ffc0, version
0x00000001
search_read_bbts() search mirror
table
search_bbt() ...1; mtd->size ==
0x08000000
search_bbt() ...2; maxblocks: 0x00000004; mtd->size ==
0x08000000
Block:
0x000003ff
Block:
0x000003fe
Check, if we found a bbt for each requested
chip
Bad block table found at page0x0000ff80, version
0x00000001
scan_bbt()
...3
Done.
Chip identified... 3; NAND 128MiB 3,3V
8-bit
type:
0x00000004
flags:
0x000000c5
size:
0x08000000
erasesize:
0x00020000
oobblock:
0x00000800
oobsize:
0x00000040
ecctype:
0x00000002
eccsize:
0x00000100
Oob
info:
useecc:
0x00000002
eccbytes:
0x00000018
eccpos: 0x00000028 0x00000029 0x0000002a 0x0000002b 0x0000002c 0x0000002d
0x0000002e 0x0000002f 0x00000030 0x00000031 0x00000032 0x00000033
0x00000034 0x00000035 0x00000036 0x00
Bootload in
progress...
New block 0x00040000;len: 0x00200000;start:
0x00040000
New block 0x00060000;len: 0x001e0000;start:
0x00060000
New block 0x00080000;len: 0x001c0000;start:
0x00080000
New block 0x000a0000;len: 0x001a0000;start:
0x000a0000
New block 0x000c0000;len: 0x00180000;start:
0x000c0000
New block 0x000e0000;len: 0x00160000;start:
0x000e0000
New block 0x00100000;len: 0x00140000;start:
0x00100000
New block 0x00120000;len: 0x00120000;start:
0x00120000
New block 0x00140000;len: 0x00100000;start:
0x00140000
New block 0x00160000;len: 0x000e0000;start:
0x00160000
New block 0x00180000;len: 0x000c0000;start:
0x00180000
New block 0x001a0000;len: 0x000a0000;start:
0x001a0000
New block 0x001c0000;len: 0x00080000;start:
0x001c0000
New block 0x001e0000;len: 0x00060000;start:
0x001e0000
New block 0x00200000;len: 0x00040000;start:
0x00200000
New block 0x00220000;len: 0x00020000;start:
0x00220000
complete, status 0x00000000, loaded 0x00200000
bytes
Data in
DRAM:
0x25f005b0 0x009cedff
0xbeef05b0
Booting...
Uncompressing
Linux...
Done. Now booting the
kernel.
Linux version 2.6.19 (oleg at eyesisboxus) (gcc version 3.2.1 Axis release
R64/1.64) #2 Sun Jan 15 18:43:42 MST
2012
Setting up paging and the
MMU.
Linux/CRISv32 port on ETRAX FS (C) 2003, 2004 Axis Communications
AB
Built 1 zonelists. Total pages:
8160
Kernel command line: root=/dev/mtdblock3 init=/linuxrc
rootfstype=jffs2
PID hash table entries: 256 (order: 8, 1024
bytes)
Dentry cache hash table entries: 8192 (order: 2, 32768
bytes)
Inode-cache hash table entries: 4096 (order: 1, 16384
bytes)
Memory: 40304k/65536k available (1744k kernel code, 25232k reserved, 622k
data, 72k
init)
Mount-cache hash table entries:
1024
NET: Registered protocol family
16
SCSI subsystem
initialized
usbcore: registered new interface driver
usbfs
usbcore: registered new interface driver
hub
usbcore: registered new device driver
usb
NET: Registered protocol family
2
IP route cache hash table entries: 512 (order: -2, 2048
bytes)
TCP established hash table entries: 2048 (order: 0, 8192
bytes)
TCP bind hash table entries: 1024 (order: -1, 4096
bytes)
TCP: Hash tables configured (established 2048 bind
1024)
TCP reno
registered
Check hardware configuration of Elphel 353
camera
Elphel 10349/10369 IO extension board is
present
fast_timer_init()
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat,
Inc.
io scheduler noop registered
(default)
Serial: CRISv32 driver $Revision: 1.78 $ <6>ttyS0 at I/O 0xb0026000 (irq =
68) is a
CRISv32
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024
blocksize
PPP generic driver version
2.4.2
ETRAX FS 10/100MBit ethernet v0.01 (c) 2003 Axis Communications
AB
eth0: changed MAC to
00:40:8C:CD:00:00
Uniform Multi-Platform E-IDE driver Revision:
7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
ide: ETRAX FS built-in ATA DMA
controller
cris_ide_init()
hda: FUJITSU MHX2300BT, ATA DISK
drive
ide0 at 0x10000000-0x10000007,0x2c000000 on irq
65
hda: max request size:
128KiB
hda: 586072368 sectors (300069 MB) w/8192KiB Cache, CHS=36481/255/63,
(U)DMA
hda: cache flushes
supported
hda:
hda1
Initializing USB Mass Storage
driver...
usbcore: registered new interface driver
usb-storage
USB Mass Storage support
registered.
usbcore: registered new interface driver
usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for
generic
usbcore: registered new interface driver
usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver
core
drivers/usb/serial/usb-serial.c: USB Serial support registered for Belkin /
Peracom / GoHubs USB Serial
Adapter
usbcore: registered new interface driver
belkin
drivers/usb/serial/belkin_sa.c: USB Belkin Serial converter driver
v1.2
drivers/usb/serial/usb-serial.c: USB Serial support registered for
cp2101
usbcore: registered new interface driver
cp2101
drivers/usb/serial/cp2101.c: Silicon Labs CP2101/CP2102 RS232 serial
adaptor driver
v0.07
drivers/usb/serial/usb-serial.c: USB Serial support registered for Garmin
GPS
usb/tty
usbcore: registered new interface driver
garmin_gps
drivers/usb/serial/garmin_gps.c: garmin gps driver
v0.28
drivers/usb/serial/usb-serial.c: USB Serial support registered for MCT
U232
usbcore: registered new interface driver
mct_u232
drivers/usb/serial/mct_u232.c: Magic Control Technology USB-RS232 converter
driver
z2.0
drivers/usb/serial/usb-serial.c: USB Serial support registered for
pl2303
usbcore: registered new interface driver
pl2303
drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor
driver
ETRAX FS stream co-processor driver v0.01, (c) 2003 Axis Communications
AB
stream co-processor: init
done.
axisflashmap:
...
NAND device: Manufacturer ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB
3,3V
8-bit)
Additional Info: ID byte3=0x0,
byte4=0x1d
Flash is rated 30 ns, modifying bif_core_rw_grp3: old=0x6300483,
new=0x6300001
NAND 128MiB 3,3V 8-bit: 0x08000000 bytes of NAND flash
memory.
axisflashmap: Set to boot from NAND flash, making NAND flash primary
device.
axisflashmap: flash read 512 bytes at 0x00040000, data: 00 b0 05 f0 25 ff
ed
9c
axisflashmap: partition table offset 10, data: ef be 84 00 12 0f 00
00
axisflashmap: Found a valid partition table at
0xc03019ae-0xc0301a3a.
offset == 0x00040000, size ==
0x007C0000
offset == 0x00800000, size ==
0x01800000
offset == 0x02000000, size ==
0x05000000
offset == 0x07000000, size ==
0x00C00000
Creating 1 MTD partitions on "NAND 128MiB 3,3V
8-bit":
0x00000000-0x08000000 :
"main"
Creating 1 MTD partitions on "NAND 128MiB 3,3V
8-bit":
0x00000000-0x00040000 :
"part0"
Creating 1 MTD partitions on "NAND 128MiB 3,3V
8-bit":
0x00040000-0x00800000 :
"part1"
Creating 1 MTD partitions on "NAND 128MiB 3,3V
8-bit":
0x00800000-0x02000000 :
"part2"
Creating 1 MTD partitions on "NAND 128MiB 3,3V
8-bit":
0x02000000-0x07000000 :
"part3"
Creating 1 MTD partitions on "NAND 128MiB 3,3V
8-bit":
0x07000000-0x07c00000 :
"part4"
ETRAX FS GPIO driver v2.5, (c) 2003-2006 Axis Communications
AB
Elphel (R) model 353 FPGA (Xilinx (R) XC3S1200E) configuration driver -
132
Elphel (R) model 353 system clocks (PLL frequency synth.) driver -
133
fpga_control-
129
arch/cris/arch-v32/drivers/elphel/framepars.c:390:initGlobalPars
GLOBALPARS(G_DEBUG)=0
arch/cris/arch-v32/drivers/elphel/framepars.c:420:initMultiPars
GLOBALPARS(G_MULTI_NUM)=0
Elphel (R) Model 353 Frame Parameters device driver -
130
Elphel FPGA interrupts
initialized
Initializing DMA registers for EXTDMA3 - Elphel (R) Model 353 Camera Driver
-
126
Elphel (R) model 353 i2c character device driver - 134, 2
channels
Raw image access driver-
131
Elphel (R) Model 353 video buffer device driver-
135
Elphel (R) model 353 Exif device driver -
125
Starting Elphel (R) Model 353 Gamma Tables device driver -
137
Elphel (R) Model 353 Gamma Tables device driver -
137
Elphel (R) Model 353 Histograms device
driver
imu_logger-
141
TCP cubic
registered
NET: Registered protocol family
1
NET: Registered protocol family
17
VFS: Mounted root (jffs2 filesystem)
readonly.
Freeing unused kernel memory: 72k
freed
/linuxrc: Mounting /mnt/flash... Empty flash at 0x00b7e238 ends at
0x00b7e800
done
/linuxrc: Starting
init.
init: starting
up.
Starting system
initialization.
Axis Linux, http://developer.axis.com/
Copyright (C) 2000-2007 Axis Communications
AB
Elphel (R) Model 353 Camera release
8.1.2
* Mounting filesystems... [
ok
]
* Initializing /var... [
ok
]
* Determining MAC
address...
+ using saved MAC address: 00:0E:64:08:1A:0D [
ok
]
* Initializing random number generator... [
ok
]
* Setting
hostname...
+ hostname: "Elphel353" [
ok
]
* Initializing volatile resolver configuration... [
ok
]
* Setting FPGA master clock to 160 MHz... [
ok
]
* Programming FPGA with /etc/x353.bit... [
ok
]
* Loaded FPGA rev... [
353402b
]
* Adjusting DDR SDRAM clock phase... [
PH 90/14
]
* Turn on xtall output (12MHz) to FPGA... [
ok
]
* Some CMOS-based sensor board attached... [
assuming 10338
]
* Configure broadcast ping... [
ok
]
System initialization is
done.
/bin/sh: can't access tty; job control turned
off
# New runlevel:
3
* Starting respawn daemon... [
ok
]
* Starting system and kernel
logger...
Jan 1 00:00:17 Elphel353 syslogd 1.4.1:
restart.
+ system logger
started
+ kernel logger started [
ok
]
* Bringing lo up... [
ok
]
* Bringing eth0
up...
eth0: changed MAC to
00:0E:64:08:1A:0D
+ hardware address:
00:0E:64:08:1A:0D
+ media:
auto
+ eth0 going
up
eth0: changed MAC to
00:0E:64:08:1A:0D
+ IPv4 on
eth0
+ boot protocol:
none
+ IP address:
192.168.0.9
+ netmask:
255.255.255.0
+ broadcast address:
192.168.0.255
+ default IPv4 gateway:
192.168.0.15
+ set MDI to MDI (normal)
mode
y
+ done [
ok
]
* Waiting for a network
interface...
+ eth0 is up [
ok ]
* Starting ipsetd...
Jan 1 00:00:20 Elphel353 ipsetd[709]: Timeout in 120 s.
Jan 1 00:00:20 Elphel353 ipsetd[709]: Expecting echo request payload 408
bytes.
Jan 1 00:00:20 Elphel353 ipsetd[709]: On echo request arrival, execute [
ok ]psetd.script.
* Starting telnet server...
telnetd: starting
port: 23; interface: any; login program: /bin/login;
maximum number of allowed simultaneous clients: unlimited [
ok ]
* Starting ftp server...
Jan 1 00:00:20 Elphel353 vftpd[715]: Starting vftpd 0.01
Jan 1 00:00:20 Elphel353 vftpd[716]: qos_setup_socket: unsupported AF [
ok ]
* Starting ssh server... [
ok ]
* Starting mii-diag... [
ok ]
* Starting image server on port 8081, making Exif...
Jan 1 00:00:21 Elphel353 dropbear[727]: Running in background [
ok ]
* Flushing JFFS2 (sync)... [
ok ]
* Starting autocampars daemon... [
ok ]
* Starting autoexposure daemon...
autoexposure started, daemon_bit=0x0, debug=0x1
autoexposure.c:126:main: autoexposure started, daemon_bit=0x0, debug=0x1[
ok ]
* Starting ccamftp daemon... [
ok ]
* initializing camera/sensor parameters...
arch/cris/arch-v32/drivers/elphel/framepars.c:390:initGlobalPars
GLOBALPARS(G_DEBUG)=0
initSequencers:resetting both sequencers
arch/cris/arch-v32/drivers/elphel/framepars.c:420:initMultiPars
GLOBALPARS(G_MULTI_NUM)=0
sensor clock set to 20000000
removing MRST from the sensor
Found MT9P001 2592x1944 sensor, chip ID=1801
trying MT9P001
Resetting MT9X001 sensor
Reading sensor registers to the shadows:
Initializing MT9X001 registers with default values:
Starting hardware sequencers [
ok ]
* Starting lighttpd web server... [
ok ]
* Setting time from NTP server... [
Mon Mar 19 19:18:27 UTC 2012 ]
+ Setting FPGA time from the system time
* Looking for I/O board... [
10369"A" ]
ETRAX FS IOP USB Host Controller version 1.10 (c) 2004, 2005, 2006
Axis Communications AB
crisv32_hc crisv32_hc.0: ETRAX FS IOP USB Host Controller
crisv32_hc crisv32_hc.0: new USB bus registered, assigned bus number 1
crisv32_hc crisv32_hc.0: irq 51, io base 0x00000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
crisv32_hc crisv32_hc.0: ETRAX FS IOP USB Host Controller
usbcore: registered new interface driver snd-usb-audio
usbcore: registered new interface driver snd-usb-caiaq
* Initializing USB hub... [
ok ]
* Setting CMOS clock from the system time...
usb 1-1: new full speed USB device using crisv32_hc and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected [
ok ]
* Starting video streamer... [
ok ]
* Starting IMU/GPS/compass... [
none ]
launcher: nothing to launch
All scripts for runlevel 3 done in 74.94s.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://support.elphel.com/pipermail/support-list_support.elphel.com/attachments/20120319/8caa266d/attachment-0002.html>
More information about the Support-list
mailing list